From 710ca71ba346acb7478119c58e869416154055ca Mon Sep 17 00:00:00 2001
From: Robin Mueller <robin.mueller.m@gmail.com>
Date: Mon, 8 Nov 2021 01:14:25 +0100
Subject: [PATCH] added utility files

---
 .cargo/config.toml | 36 ++++++++++++++++++++++++++++++++++++
 jlink.gdb          | 10 ++++++++++
 memory.x           | 10 ++++++++++
 3 files changed, 56 insertions(+)
 create mode 100644 .cargo/config.toml
 create mode 100644 jlink.gdb
 create mode 100644 memory.x

diff --git a/.cargo/config.toml b/.cargo/config.toml
new file mode 100644
index 0000000..dd54ddd
--- /dev/null
+++ b/.cargo/config.toml
@@ -0,0 +1,36 @@
+[target.'cfg(all(target_arch = "arm", target_os = "none"))']
+# uncomment ONE of these three option to make `cargo run` start a GDB session
+# which option to pick depends on your system
+# runner = "arm-none-eabi-gdb -q -x jlink.gdb"
+# runner = "gdb-multiarch -q -x jlink.gdb"
+# runner = "gdb -q -x openocd.gdb"
+
+rustflags = [
+  # This is needed if your flash or ram addresses are not aligned to 0x10000 in memory.x
+  # See https://github.com/rust-embedded/cortex-m-quickstart/pull/95
+  "-C", "link-arg=--nmagic",
+
+  # LLD (shipped with the Rust toolchain) is used as the default linker
+  "-C", "link-arg=-Tlink.x",
+
+  # if you run into problems with LLD switch to the GNU linker by commenting out
+  # this line
+  # "-C", "linker=arm-none-eabi-ld",
+
+  # if you need to link to pre-compiled C libraries provided by a C toolchain
+  # use GCC as the linker by commenting out both lines above and then
+  # uncommenting the three lines below
+  # "-C", "linker=arm-none-eabi-gcc",
+  # "-C", "link-arg=-Wl,-Tlink.x",
+  # "-C", "link-arg=-nostartfiles",
+]
+
+[build]
+# Pick ONE of these compilation targets
+target = "thumbv6m-none-eabi"        # Cortex-M0 and Cortex-M0+
+# target = "thumbv7m-none-eabi"        # Cortex-M3
+# target = "thumbv7em-none-eabi"       # Cortex-M4 and Cortex-M7 (no FPU)
+# target = "thumbv7em-none-eabihf"     # Cortex-M4F and Cortex-M7F (with FPU)
+# target = "thumbv8m.base-none-eabi"   # Cortex-M23
+# target = "thumbv8m.main-none-eabi"   # Cortex-M33 (no FPU)
+# target = "thumbv8m.main-none-eabihf" # Cortex-M33 (with FPU)
\ No newline at end of file
diff --git a/jlink.gdb b/jlink.gdb
new file mode 100644
index 0000000..20ff2d5
--- /dev/null
+++ b/jlink.gdb
@@ -0,0 +1,10 @@
+target remote localhost:2331
+
+monitor reset
+
+# *try* to stop at the user entry point (it might be gone due to inlining)
+break main
+
+load
+
+continue
diff --git a/memory.x b/memory.x
new file mode 100644
index 0000000..1ca0e97
--- /dev/null
+++ b/memory.x
@@ -0,0 +1,10 @@
+MEMORY
+{
+	FLASH : ORIGIN = 0x00000000, LENGTH = 0x20000 /* 128K */
+	RAM : ORIGIN = 0x10000000, LENGTH = 0x08000 /* 32K */
+}
+
+/* This is where the call stack will be allocated. */
+/* The stack is of the full descending type. */
+/* NOTE Do NOT modify `_stack_start` unless you know what you are doing */
+_stack_start = ORIGIN(RAM) + LENGTH(RAM);