Merge branch 'main' of https://egit.irs.uni-stuttgart.de/rust/va108xx-hal

.github/workflows/ci.yml

@@ -16,14 +16,11 @@ jobs:
           override: true
       - uses: actions-rs/cargo@v1
         with:
-          use-cross: true
           command: check
-          args: --target thumbv6m-none-eabi
       - uses: actions-rs/cargo@v1
         with:
-          use-cross: true
           command: check
-          args: --examples --target thumbv6m-none-eabi
+          args: --examples
 
   fmt:
     name: Rustfmt
@@ -55,9 +52,8 @@ jobs:
       - run: rustup component add clippy
       - uses: actions-rs/cargo@v1
         with:
-          use-cross: true
           command: clippy
-          args: --target thumbv6m-none-eabi -- -D warnings
+          args: -- -D warnings
 
   ci:
       if: ${{ success() }}

Cargo.toml

@@ -36,10 +36,15 @@ debug = true
 lto = false
 
 [profile.release]
-lto = true
+# Problematic because RTT won't work
+lto = false
 debug = true
 opt-level = "s"
 
+[profile.release-lto]
+inherits = "release"
+lto = true
+
 [[example]]
 name = "timer-ticks"
 required-features = ["rt"]

README.md

@@ -85,4 +85,4 @@ is contained within the
 
 7. Flashing the board might work differently for different boards and there is usually
    more than one way. You can find example instructions for the REB1 development board
-   [here](https://github.com/robamu-org/vorago-reb1-rs).
+   [here](https://egit.irs.uni-stuttgart.de/rust/vorago-reb1).

examples/blinky-pac.rs

@@ -0,0 +1,48 @@
+
+//! Blinky examples using only the PAC
+//!
+//! Additional note on LEDs:
+//! Pulling the GPIOs low makes the LEDs blink. See REB1
+//! schematic for more details.
+#![no_main]
+#![no_std]
+
+use cortex_m_rt::entry;
+use panic_halt as _;
+use va108xx as pac;
+
+// REB LED pin definitions. All on port A
+const LED_D2: u32 = 1 << 10;
+const LED_D3: u32 = 1 << 7;
+const LED_D4: u32 = 1 << 6;
+
+#[entry]
+fn main() -> ! {
+    let dp = pac::Peripherals::take().unwrap();
+    // Enable all peripheral clocks
+    dp.SYSCONFIG
+        .peripheral_clk_enable
+        .modify(|_, w| unsafe { w.bits(0xffffffff) });
+    dp.PORTA
+        .dir()
+        .modify(|_, w| unsafe { w.bits(LED_D2 | LED_D3 | LED_D4) });
+    dp.PORTA
+        .datamask()
+        .modify(|_, w| unsafe { w.bits(LED_D2 | LED_D3 | LED_D4) });
+    for _ in 0..10 {
+        dp.PORTA
+            .clrout()
+            .write(|w| unsafe { w.bits(LED_D2 | LED_D3 | LED_D4) });
+        cortex_m::asm::delay(5_000_000);
+        dp.PORTA
+            .setout()
+            .write(|w| unsafe { w.bits(LED_D2 | LED_D3 | LED_D4) });
+        cortex_m::asm::delay(5_000_000);
+    }
+    loop {
+        dp.PORTA
+            .togout()
+            .write(|w| unsafe { w.bits(LED_D2 | LED_D3 | LED_D4) });
+        cortex_m::asm::delay(25_000_000);
+    }
+}

src/i2c.rs

@@ -2,7 +2,7 @@
 //!
 //! ## Examples
 //!
-//! - [REB1 I2C temperature sensor example](https://github.com/robamu-org/vorago-reb1-rs/blob/main/examples/temp-sensor.rs)
+//! - [REB1 I2C temperature sensor example](https://egit.irs.uni-stuttgart.de/rust/vorago-reb1/src/branch/main/examples/adt75-temp-sensor.rs)
 use crate::{
     clock::{enable_peripheral_clock, PeripheralClocks},
     pac::{I2CA, I2CB, SYSCONFIG},