eive-obsw/bsp_q7s/OBSWConfig.h.in

144 lines
6.9 KiB
C

/**
* @brief This file can be used to add preprocessor define for conditional
* code inclusion exclusion or various other project constants and
* properties in one place.
*/
#ifndef FSFWCONFIG_OBSWCONFIG_H_
#define FSFWCONFIG_OBSWCONFIG_H_
#include "commonConfig.h"
#include "q7sConfig.h"
#include "OBSWVersion.h"
/*******************************************************************/
/** All of the following flags should be enabled for mission code */
/*******************************************************************/
#define OBSW_ADD_GOMSPACE_PCDU @OBSW_ADD_GOMSPACE_PCDU@
#define OBSW_ADD_MGT @OBSW_ADD_MGT@
#define OBSW_ADD_BPX_BATTERY_HANDLER @OBSW_ADD_BPX_BATTERY_HANDLER@
#define OBSW_ADD_STAR_TRACKER @OBSW_ADD_STAR_TRACKER@
#define OBSW_ADD_PLOC_SUPERVISOR @OBSW_ADD_PLOC_SUPERVISOR@
#define OBSW_ADD_PLOC_MPSOC @OBSW_ADD_PLOC_MPSOC@
#define OBSW_ADD_SUN_SENSORS @OBSW_ADD_SUN_SENSORS@
#define OBSW_ADD_SUS_BOARD_ASS @OBSW_ADD_SUS_BOARD_ASS@
#define OBSW_ADD_ACS_BOARD @OBSW_ADD_ACS_BOARD@
#define OBSW_ADD_ACS_CTRL 1
#define OBSW_ADD_GPS_CTRL @OBSW_ADD_GPS_CTRL@
#define OBSW_ADD_TCS_CTRL @OBSW_ADD_TCS_CTRL@
#define OBSW_ADD_RW @OBSW_ADD_RW@
#define OBSW_ADD_RTD_DEVICES @OBSW_ADD_RTD_DEVICES@
#define OBSW_ADD_SA_DEPL @OBSW_ADD_SA_DEPL@
#define OBSW_ADD_SCEX_DEVICE @OBSW_ADD_SCEX_DEVICE@
#define OBSW_ADD_HEATERS @OBSW_ADD_HEATERS@
#define OBSW_ADD_TMP_DEVICES @OBSW_ADD_TMP_DEVICES@
#define OBSW_ADD_RAD_SENSORS @OBSW_ADD_RAD_SENSORS@
#define OBSW_ADD_PL_PCDU @OBSW_ADD_PL_PCDU@
#define OBSW_ADD_SYRLINKS @OBSW_ADD_SYRLINKS@
#define OBSW_ADD_CCSDS_IP_CORES @OBSW_ADD_CCSDS_IP_CORES@
// Set to 1 if all telemetry should be sent to the PTME IP Core
#define OBSW_TM_TO_PTME @OBSW_TM_TO_PTME@
// Set to 1 if telecommands are received via the PDEC IP Core
#define OBSW_TC_FROM_PDEC @OBSW_TC_FROM_PDEC@
#define OBSW_ENABLE_SYRLINKS_TRANSMIT_TIMEOUT 0
// Configuration parameter which causes the core controller to try to keep at least one SD card
// working
#define OBSW_SD_CARD_MUST_BE_ON 1
#define OBSW_ENABLE_TIMERS 1
// This is a really tricky switch.. It initializes the PCDU switches to their default states
// at powerup. I think it would be better
// to leave it off for now. It makes testing a lot more difficult and it might mess with
// something the operators might want to do by giving the software too much intelligence
// at the wrong place. The system component might command all the Switches accordingly anyway
#define OBSW_INITIALIZE_SWITCHES 0
#define OBSW_ENABLE_PERIODIC_HK 0
/*******************************************************************/
/** All of the following flags should be disabled for mission code */
/*******************************************************************/
// Can be used to switch device to NORMAL mode immediately
#define OBSW_SWITCH_TO_NORMAL_MODE_AFTER_STARTUP 0
#define OBSW_PRINT_MISSED_DEADLINES 1
#define OBSW_MPSOC_JTAG_BOOT 0
#define OBSW_STAR_TRACKER_GROUND_CONFIG 1
#define OBSW_SYRLINKS_SIMULATED @OBSW_SYRLINKS_SIMULATED@
#define OBSW_ADD_TEST_CODE 0
#define OBSW_ADD_TEST_TASK 0
#define OBSW_ADD_TEST_PST 0
// If this is enabled, all other SPI code should be disabled
#define OBSW_ADD_SPI_TEST_CODE 0
// If this is enabled, all other I2C code should be disabled
#define OBSW_ADD_I2C_TEST_CODE 0
#define OBSW_ADD_UART_TEST_CODE 0
#define OBSW_TEST_ACS 0
#define OBSW_DEBUG_ACS 0
#define OBSW_TEST_SUS 0
#define OBSW_DEBUG_SUS 0
#define OBSW_TEST_RTD 0
#define OBSW_DEBUG_RTD 0
#define OBSW_TEST_RAD_SENSOR 0
#define OBSW_DEBUG_RAD_SENSOR 0
#define OBSW_TEST_PL_PCDU 0
#define OBSW_DEBUG_PL_PCDU 0
#define OBSW_TEST_BPX_BATT 0
#define OBSW_DEBUG_BPX_BATT 0
#define OBSW_TEST_IMTQ 0
#define OBSW_DEBUG_IMTQ 0
#define OBSW_TEST_RW 0
#define OBSW_DEBUG_RW 0
#define OBSW_TEST_LIBGPIOD 0
#define OBSW_TEST_PLOC_HANDLER 0
#define OBSW_TEST_CCSDS_BRIDGE 0
#define OBSW_TEST_CCSDS_PTME 0
#define OBSW_TEST_TE7020_HEATER 0
#define OBSW_TEST_GPIO_OPEN_BY_LABEL 0
#define OBSW_TEST_GPIO_OPEN_BY_LINE_NAME 0
#define OBSW_DEBUG_P60DOCK 0
#define OBSW_PRINT_CORE_HK 0
#define OBSW_DEBUG_PDU1 0
#define OBSW_DEBUG_PDU2 0
#define OBSW_DEBUG_TMP1075 0
#define OBSW_DEBUG_GPS 0
#define OBSW_DEBUG_ACU 0
#define OBSW_DEBUG_SYRLINKS 0
#define OBSW_DEBUG_PDEC_HANDLER 0
#define OBSW_DEBUG_PLOC_SUPERVISOR 0
#define OBSW_DEBUG_PLOC_MPSOC 0
#define OBSW_DEBUG_STARTRACKER 0
#define OBSW_TCP_SERVER_WIRETAPPING 0
/*******************************************************************/
/** CMake Defines */
/*******************************************************************/
// Use TCP instead of UDP for the TMTC bridge. This allows using the TMTC client locally
// because UDP packets are not allowed in the VPN
// This will cause the OBSW to initialize the TMTC bridge responsible for exchanging data with the
// CCSDS IP Cores.
#define OBSW_ADD_TMTC_TCP_SERVER 1
#define OBSW_ADD_TMTC_UDP_SERVER 1
#cmakedefine EIVE_BUILD_GPSD_GPS_HANDLER
#cmakedefine LIBGPS_VERSION_MAJOR @LIBGPS_VERSION_MAJOR@
#cmakedefine LIBGPS_VERSION_MINOR @LIBGPS_VERSION_MINOR@
#ifdef __cplusplus
#include "objects/systemObjectList.h"
#include "events/subsystemIdRanges.h"
#include "returnvalues/classIds.h"
#endif
#endif /* FSFWCONFIG_OBSWCONFIG_H_ */