530 lines
18 KiB
C++
530 lines
18 KiB
C++
#include "GyroL3GD20H.h"
|
|
#include "spiConf.h"
|
|
#include "../spi/mspInit.h"
|
|
#include "../spi/spiDefinitions.h"
|
|
#include "../spi/spiCore.h"
|
|
|
|
#include "fsfw/tasks/TaskFactory.h"
|
|
#include "fsfw/serviceinterface/ServiceInterface.h"
|
|
|
|
#include "stm32h7xx_nucleo.h"
|
|
#include "stm32h7xx_hal_spi.h"
|
|
#include "stm32h7xx_hal_rcc.h"
|
|
|
|
#include <cstring>
|
|
|
|
alignas(32) std::array<uint8_t, GyroL3GD20H::recvBufferSize> GyroL3GD20H::rxBuffer;
|
|
alignas(32) std::array<uint8_t, GyroL3GD20H::txBufferSize>
|
|
GyroL3GD20H::txBuffer __attribute__((section(".dma_buffer")));
|
|
|
|
TransferStates transferState = TransferStates::IDLE;
|
|
spi::TransferModes GyroL3GD20H::transferMode = spi::TransferModes::POLLING;
|
|
|
|
DMA_HandleTypeDef txDmaHandle;
|
|
DMA_HandleTypeDef rxDmaHandle;
|
|
|
|
GyroL3GD20H::GyroL3GD20H(SPI_HandleTypeDef *spiHandle, spi::TransferModes transferMode_):
|
|
spiHandle(spiHandle) {
|
|
transferMode = transferMode_;
|
|
if(transferMode == spi::TransferModes::DMA) {
|
|
spi::setDmaHandles(&txDmaHandle, &rxDmaHandle);
|
|
spi::setSpiMspFunctions(&spi::halMspInitDma, spiHandle,
|
|
&spi::halMspDeinitDma, spiHandle);
|
|
}
|
|
else if(transferMode == spi::TransferModes::INTERRUPT) {
|
|
spi::setSpiMspFunctions(&spi::halMspInitInterrupt, spiHandle,
|
|
&spi::halMspDeinitInterrupt, spiHandle);
|
|
}
|
|
else if(transferMode == spi::TransferModes::POLLING) {
|
|
spi::setSpiMspFunctions(&spi::halMspInitPolling, spiHandle,
|
|
&spi::halMspDeinitPolling, spiHandle);
|
|
}
|
|
|
|
spi::assignTransferRxTxCompleteCallback(&spiTransferCompleteCallback, nullptr);
|
|
spi::assignTransferErrorCallback(&spiTransferErrorCallback, nullptr);
|
|
|
|
GPIO_InitTypeDef chipSelect = {};
|
|
__HAL_RCC_GPIOD_CLK_ENABLE();
|
|
chipSelect.Pin = GPIO_PIN_14;
|
|
chipSelect.Mode = GPIO_MODE_OUTPUT_PP;
|
|
HAL_GPIO_Init(GPIOD, &chipSelect);
|
|
HAL_GPIO_WritePin(GPIOD, GPIO_PIN_14, GPIO_PIN_SET);
|
|
}
|
|
|
|
ReturnValue_t GyroL3GD20H::initialize() {
|
|
// Configure the SPI peripheral
|
|
spiHandle->Instance = SPI1;
|
|
spiHandle->Init.BaudRatePrescaler = spi::getPrescaler(HAL_RCC_GetHCLKFreq(), 3900000);
|
|
spiHandle->Init.Direction = SPI_DIRECTION_2LINES;
|
|
spi::assignSpiMode(spi::SpiModes::MODE_3, *spiHandle);
|
|
spiHandle->Init.DataSize = SPI_DATASIZE_8BIT;
|
|
spiHandle->Init.FirstBit = SPI_FIRSTBIT_MSB;
|
|
spiHandle->Init.TIMode = SPI_TIMODE_DISABLE;
|
|
spiHandle->Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE;
|
|
spiHandle->Init.CRCPolynomial = 7;
|
|
spiHandle->Init.CRCLength = SPI_CRC_LENGTH_8BIT;
|
|
spiHandle->Init.NSS = SPI_NSS_SOFT;
|
|
spiHandle->Init.NSSPMode = SPI_NSS_PULSE_DISABLE;
|
|
// Recommended setting to avoid glitches
|
|
spiHandle->Init.MasterKeepIOState = SPI_MASTER_KEEP_IO_STATE_ENABLE;
|
|
spiHandle->Init.Mode = SPI_MODE_MASTER;
|
|
if(HAL_SPI_Init(spiHandle) != HAL_OK) {
|
|
sif::printWarning("Error initializing SPI\n");
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
|
|
transferState = TransferStates::WAIT;
|
|
|
|
sif::printInfo("GyroL3GD20H::performOperation: Reading WHO AM I register\n");
|
|
|
|
txBuffer[0] = WHO_AM_I_REG | STM_READ_MASK;
|
|
txBuffer[1] = 0;
|
|
|
|
switch(transferMode) {
|
|
case(spi::TransferModes::DMA): {
|
|
return handleDmaTransferInit();
|
|
}
|
|
case(spi::TransferModes::INTERRUPT): {
|
|
return handleInterruptTransferInit();
|
|
}
|
|
case(spi::TransferModes::POLLING): {
|
|
return handlePollingTransferInit();
|
|
}
|
|
default: {
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
}
|
|
|
|
return HasReturnvaluesIF::RETURN_OK;
|
|
}
|
|
|
|
ReturnValue_t GyroL3GD20H::performOperation() {
|
|
switch(transferMode) {
|
|
case(spi::TransferModes::DMA): {
|
|
return handleDmaSensorRead();
|
|
}
|
|
case(spi::TransferModes::POLLING): {
|
|
return handlePollingSensorRead();
|
|
}
|
|
case(spi::TransferModes::INTERRUPT): {
|
|
return handleInterruptSensorRead();
|
|
}
|
|
default: {
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
}
|
|
return HasReturnvaluesIF::RETURN_OK;
|
|
}
|
|
|
|
ReturnValue_t GyroL3GD20H::handleDmaTransferInit() {
|
|
/* Clean D-cache */
|
|
/* Make sure the address is 32-byte aligned and add 32-bytes to length,
|
|
in case it overlaps cacheline */
|
|
// See https://community.st.com/s/article/FAQ-DMA-is-not-working-on-STM32H7-devices
|
|
HAL_StatusTypeDef result = performDmaTransfer(2);
|
|
if(result != HAL_OK) {
|
|
// Transfer error in transmission process
|
|
sif::printWarning("GyroL3GD20H::initialize: Error transmitting SPI with DMA\n");
|
|
}
|
|
|
|
// Wait for the transfer to complete
|
|
while (transferState == TransferStates::WAIT) {
|
|
TaskFactory::delayTask(1);
|
|
}
|
|
|
|
switch(transferState) {
|
|
case(TransferStates::SUCCESS): {
|
|
uint8_t whoAmIVal = rxBuffer[1];
|
|
if(whoAmIVal != EXPECTED_WHO_AM_I_VAL) {
|
|
sif::printDebug("GyroL3GD20H::initialize: "
|
|
"Read WHO AM I value %d not equal to expected value!\n", whoAmIVal);
|
|
}
|
|
transferState = TransferStates::IDLE;
|
|
break;
|
|
}
|
|
case(TransferStates::FAILURE): {
|
|
sif::printWarning("Transfer failure\n");
|
|
transferState = TransferStates::FAILURE;
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
default: {
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
}
|
|
|
|
sif::printInfo("GyroL3GD20H::initialize: Configuring device\n");
|
|
// Configure the 5 configuration registers
|
|
uint8_t configRegs[5];
|
|
prepareConfigRegs(configRegs);
|
|
|
|
result = performDmaTransfer(6);
|
|
if(result != HAL_OK) {
|
|
// Transfer error in transmission process
|
|
sif::printWarning("Error transmitting SPI with DMA\n");
|
|
}
|
|
|
|
// Wait for the transfer to complete
|
|
while (transferState == TransferStates::WAIT) {
|
|
TaskFactory::delayTask(1);
|
|
}
|
|
|
|
switch(transferState) {
|
|
case(TransferStates::SUCCESS): {
|
|
sif::printInfo("GyroL3GD20H::initialize: Configuration transfer success\n");
|
|
transferState = TransferStates::IDLE;
|
|
break;
|
|
}
|
|
case(TransferStates::FAILURE): {
|
|
sif::printWarning("GyroL3GD20H::initialize: Configuration transfer failure\n");
|
|
transferState = TransferStates::FAILURE;
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
default: {
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
}
|
|
|
|
|
|
txBuffer[0] = CTRL_REG_1 | STM_AUTO_INCREMENT_MASK | STM_READ_MASK;
|
|
std::memset(txBuffer.data() + 1, 0 , 5);
|
|
result = performDmaTransfer(6);
|
|
if(result != HAL_OK) {
|
|
// Transfer error in transmission process
|
|
sif::printWarning("Error transmitting SPI with DMA\n");
|
|
}
|
|
// Wait for the transfer to complete
|
|
while (transferState == TransferStates::WAIT) {
|
|
TaskFactory::delayTask(1);
|
|
}
|
|
|
|
switch(transferState) {
|
|
case(TransferStates::SUCCESS): {
|
|
if(rxBuffer[1] != configRegs[0] or rxBuffer[2] != configRegs[1] or
|
|
rxBuffer[3] != configRegs[2] or rxBuffer[4] != configRegs[3] or
|
|
rxBuffer[5] != configRegs[4]) {
|
|
sif::printWarning("GyroL3GD20H::initialize: Configuration failure\n");
|
|
}
|
|
else {
|
|
sif::printInfo("GyroL3GD20H::initialize: Configuration success\n");
|
|
}
|
|
transferState = TransferStates::IDLE;
|
|
break;
|
|
}
|
|
case(TransferStates::FAILURE): {
|
|
sif::printWarning("GyroL3GD20H::initialize: Configuration transfer failure\n");
|
|
transferState = TransferStates::FAILURE;
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
default: {
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
}
|
|
return HasReturnvaluesIF::RETURN_OK;
|
|
}
|
|
|
|
ReturnValue_t GyroL3GD20H::handleDmaSensorRead() {
|
|
txBuffer[0] = CTRL_REG_1 | STM_AUTO_INCREMENT_MASK | STM_READ_MASK;
|
|
std::memset(txBuffer.data() + 1, 0 , 14);
|
|
|
|
HAL_StatusTypeDef result = performDmaTransfer(15);
|
|
if(result != HAL_OK) {
|
|
// Transfer error in transmission process
|
|
sif::printDebug("GyroL3GD20H::handleDmaSensorRead: Error transmitting SPI with DMA\n");
|
|
}
|
|
// Wait for the transfer to complete
|
|
while (transferState == TransferStates::WAIT) {
|
|
TaskFactory::delayTask(1);
|
|
}
|
|
|
|
switch(transferState) {
|
|
case(TransferStates::SUCCESS): {
|
|
handleSensorReadout();
|
|
break;
|
|
}
|
|
case(TransferStates::FAILURE): {
|
|
sif::printWarning("GyroL3GD20H::handleDmaSensorRead: Sensor read failure\n");
|
|
transferState = TransferStates::FAILURE;
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
default: {
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
}
|
|
return HasReturnvaluesIF::RETURN_OK;
|
|
}
|
|
|
|
HAL_StatusTypeDef GyroL3GD20H::performDmaTransfer(size_t sendSize) {
|
|
transferState = TransferStates::WAIT;
|
|
#if STM_USE_PERIPHERAL_TX_BUFFER_MPU_PROTECTION == 0
|
|
SCB_CleanDCache_by_Addr((uint32_t*)(((uint32_t)txBuffer.data()) & ~(uint32_t)0x1F),
|
|
txBuffer.size()+32);
|
|
#endif
|
|
|
|
// Start SPI transfer via DMA
|
|
HAL_GPIO_WritePin(GPIOD, GPIO_PIN_14, GPIO_PIN_RESET);
|
|
return HAL_SPI_TransmitReceive_DMA(spiHandle, txBuffer.data(), rxBuffer.data(), sendSize);
|
|
}
|
|
|
|
ReturnValue_t GyroL3GD20H::handlePollingTransferInit() {
|
|
HAL_GPIO_WritePin(GPIOD, GPIO_PIN_14, GPIO_PIN_RESET);
|
|
auto result = HAL_SPI_TransmitReceive(spiHandle, txBuffer.data(), rxBuffer.data(), 2, 1000);
|
|
HAL_GPIO_WritePin(GPIOD, GPIO_PIN_14, GPIO_PIN_SET);
|
|
switch(result) {
|
|
case(HAL_OK): {
|
|
sif::printInfo("GyroL3GD20H::initialize: Polling transfer success\n");
|
|
uint8_t whoAmIVal = rxBuffer[1];
|
|
if(whoAmIVal != EXPECTED_WHO_AM_I_VAL) {
|
|
sif::printDebug("GyroL3GD20H::performOperation: "
|
|
"Read WHO AM I value %d not equal to expected value!\n", whoAmIVal);
|
|
}
|
|
break;
|
|
}
|
|
case(HAL_TIMEOUT): {
|
|
sif::printDebug("GyroL3GD20H::initialize: Polling transfer timeout\n");
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
case(HAL_ERROR): {
|
|
sif::printDebug("GyroL3GD20H::initialize: Polling transfer failure\n");
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
default: {
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
}
|
|
return HasReturnvaluesIF::RETURN_OK;
|
|
|
|
sif::printInfo("GyroL3GD20H::initialize: Configuring device\n");
|
|
// Configure the 5 configuration registers
|
|
uint8_t configRegs[5];
|
|
prepareConfigRegs(configRegs);
|
|
|
|
HAL_GPIO_WritePin(GPIOD, GPIO_PIN_14, GPIO_PIN_RESET);
|
|
result = HAL_SPI_TransmitReceive(spiHandle, txBuffer.data(), rxBuffer.data(), 6, 1000);
|
|
HAL_GPIO_WritePin(GPIOD, GPIO_PIN_14, GPIO_PIN_SET);
|
|
switch(result) {
|
|
case(HAL_OK): {
|
|
break;
|
|
}
|
|
case(HAL_TIMEOUT): {
|
|
sif::printDebug("GyroL3GD20H::initialize: Polling transfer timeout\n");
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
case(HAL_ERROR): {
|
|
sif::printDebug("GyroL3GD20H::initialize: Polling transfer failure\n");
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
default: {
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
}
|
|
return HasReturnvaluesIF::RETURN_OK;
|
|
|
|
txBuffer[0] = CTRL_REG_1 | STM_AUTO_INCREMENT_MASK | STM_READ_MASK;
|
|
std::memset(txBuffer.data() + 1, 0 , 5);
|
|
|
|
HAL_GPIO_WritePin(GPIOD, GPIO_PIN_14, GPIO_PIN_RESET);
|
|
result = HAL_SPI_TransmitReceive(spiHandle, txBuffer.data(), rxBuffer.data(), 6, 1000);
|
|
HAL_GPIO_WritePin(GPIOD, GPIO_PIN_14, GPIO_PIN_SET);
|
|
switch(result) {
|
|
case(HAL_OK): {
|
|
if(rxBuffer[1] != configRegs[0] or rxBuffer[2] != configRegs[1] or
|
|
rxBuffer[3] != configRegs[2] or rxBuffer[4] != configRegs[3] or
|
|
rxBuffer[5] != configRegs[4]) {
|
|
sif::printWarning("GyroL3GD20H::initialize: Configuration failure\n");
|
|
}
|
|
else {
|
|
sif::printInfo("GyroL3GD20H::initialize: Configuration success\n");
|
|
}
|
|
break;
|
|
}
|
|
case(HAL_TIMEOUT): {
|
|
sif::printDebug("GyroL3GD20H::initialize: Polling transfer timeout\n");
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
case(HAL_ERROR): {
|
|
sif::printDebug("GyroL3GD20H::initialize: Polling transfer failure\n");
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
default: {
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
}
|
|
return HasReturnvaluesIF::RETURN_OK;
|
|
}
|
|
|
|
ReturnValue_t GyroL3GD20H::handlePollingSensorRead() {
|
|
txBuffer[0] = CTRL_REG_1 | STM_AUTO_INCREMENT_MASK | STM_READ_MASK;
|
|
std::memset(txBuffer.data() + 1, 0 , 14);
|
|
HAL_GPIO_WritePin(GPIOD, GPIO_PIN_14, GPIO_PIN_RESET);
|
|
auto result = HAL_SPI_TransmitReceive(spiHandle, txBuffer.data(), rxBuffer.data(), 15, 1000);
|
|
HAL_GPIO_WritePin(GPIOD, GPIO_PIN_14, GPIO_PIN_SET);
|
|
switch(result) {
|
|
case(HAL_OK): {
|
|
handleSensorReadout();
|
|
break;
|
|
}
|
|
case(HAL_TIMEOUT): {
|
|
sif::printDebug("GyroL3GD20H::initialize: Polling transfer timeout\n");
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
case(HAL_ERROR): {
|
|
sif::printDebug("GyroL3GD20H::initialize: Polling transfer failure\n");
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
default: {
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
}
|
|
return HasReturnvaluesIF::RETURN_OK;
|
|
}
|
|
|
|
ReturnValue_t GyroL3GD20H::handleInterruptTransferInit() {
|
|
HAL_GPIO_WritePin(GPIOD, GPIO_PIN_14, GPIO_PIN_RESET);
|
|
switch(HAL_SPI_TransmitReceive_IT(spiHandle, txBuffer.data(), rxBuffer.data(), 2)) {
|
|
case(HAL_OK): {
|
|
sif::printInfo("GyroL3GD20H::initialize: Interrupt transfer success\n");
|
|
// Wait for the transfer to complete
|
|
while (transferState == TransferStates::WAIT) {
|
|
TaskFactory::delayTask(1);
|
|
}
|
|
|
|
uint8_t whoAmIVal = rxBuffer[1];
|
|
if(whoAmIVal != EXPECTED_WHO_AM_I_VAL) {
|
|
sif::printDebug("GyroL3GD20H::initialize: "
|
|
"Read WHO AM I value %d not equal to expected value!\n", whoAmIVal);
|
|
}
|
|
break;
|
|
}
|
|
case(HAL_BUSY):
|
|
case(HAL_ERROR):
|
|
case(HAL_TIMEOUT): {
|
|
sif::printDebug("GyroL3GD20H::initialize: Initialization failure using interrupts\n");
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
}
|
|
|
|
sif::printInfo("GyroL3GD20H::initialize: Configuring device\n");
|
|
transferState = TransferStates::WAIT;
|
|
// Configure the 5 configuration registers
|
|
uint8_t configRegs[5];
|
|
prepareConfigRegs(configRegs);
|
|
HAL_GPIO_WritePin(GPIOD, GPIO_PIN_14, GPIO_PIN_RESET);
|
|
switch(HAL_SPI_TransmitReceive_IT(spiHandle, txBuffer.data(), rxBuffer.data(), 6)) {
|
|
case(HAL_OK): {
|
|
// Wait for the transfer to complete
|
|
while (transferState == TransferStates::WAIT) {
|
|
TaskFactory::delayTask(1);
|
|
}
|
|
break;
|
|
}
|
|
case(HAL_BUSY):
|
|
case(HAL_ERROR):
|
|
case(HAL_TIMEOUT): {
|
|
sif::printDebug("GyroL3GD20H::initialize: Initialization failure using interrupts\n");
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
}
|
|
|
|
txBuffer[0] = CTRL_REG_1 | STM_AUTO_INCREMENT_MASK | STM_READ_MASK;
|
|
std::memset(txBuffer.data() + 1, 0 , 5);
|
|
transferState = TransferStates::WAIT;
|
|
HAL_GPIO_WritePin(GPIOD, GPIO_PIN_14, GPIO_PIN_RESET);
|
|
switch(HAL_SPI_TransmitReceive_IT(spiHandle, txBuffer.data(), rxBuffer.data(), 6)) {
|
|
case(HAL_OK): {
|
|
// Wait for the transfer to complete
|
|
while (transferState == TransferStates::WAIT) {
|
|
TaskFactory::delayTask(1);
|
|
}
|
|
if(rxBuffer[1] != configRegs[0] or rxBuffer[2] != configRegs[1] or
|
|
rxBuffer[3] != configRegs[2] or rxBuffer[4] != configRegs[3] or
|
|
rxBuffer[5] != configRegs[4]) {
|
|
sif::printWarning("GyroL3GD20H::initialize: Configuration failure\n");
|
|
}
|
|
else {
|
|
sif::printInfo("GyroL3GD20H::initialize: Configuration success\n");
|
|
}
|
|
break;
|
|
}
|
|
case(HAL_BUSY):
|
|
case(HAL_ERROR):
|
|
case(HAL_TIMEOUT): {
|
|
sif::printDebug("GyroL3GD20H::initialize: Initialization failure using interrupts\n");
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
}
|
|
return HasReturnvaluesIF::RETURN_OK;
|
|
}
|
|
|
|
ReturnValue_t GyroL3GD20H::handleInterruptSensorRead() {
|
|
transferState = TransferStates::WAIT;
|
|
txBuffer[0] = CTRL_REG_1 | STM_AUTO_INCREMENT_MASK | STM_READ_MASK;
|
|
std::memset(txBuffer.data() + 1, 0 , 14);
|
|
HAL_GPIO_WritePin(GPIOD, GPIO_PIN_14, GPIO_PIN_RESET);
|
|
switch(HAL_SPI_TransmitReceive_IT(spiHandle, txBuffer.data(), rxBuffer.data(), 15)) {
|
|
case(HAL_OK): {
|
|
// Wait for the transfer to complete
|
|
while (transferState == TransferStates::WAIT) {
|
|
TaskFactory::delayTask(1);
|
|
}
|
|
handleSensorReadout();
|
|
break;
|
|
}
|
|
case(HAL_BUSY):
|
|
case(HAL_ERROR):
|
|
case(HAL_TIMEOUT): {
|
|
sif::printDebug("GyroL3GD20H::initialize: Sensor read failure using interrupts\n");
|
|
return HasReturnvaluesIF::RETURN_FAILED;
|
|
}
|
|
}
|
|
return HasReturnvaluesIF::RETURN_OK;
|
|
}
|
|
|
|
void GyroL3GD20H::prepareConfigRegs(uint8_t* configRegs) {
|
|
// Enable sensor
|
|
configRegs[0] = 0b00001111;
|
|
configRegs[1] = 0b00000000;
|
|
configRegs[2] = 0b00000000;
|
|
configRegs[3] = 0b01000000;
|
|
// Big endian select
|
|
configRegs[4] = 0b00000000;
|
|
|
|
txBuffer[0] = CTRL_REG_1 | STM_AUTO_INCREMENT_MASK;
|
|
std::memcpy(txBuffer.data() + 1, configRegs, 5);
|
|
}
|
|
|
|
void GyroL3GD20H::handleSensorReadout() {
|
|
uint8_t statusReg = rxBuffer[8];
|
|
int16_t gyroXRaw = rxBuffer[9] << 8 | rxBuffer[10];
|
|
float gyroX = static_cast<float>(gyroXRaw) / INT16_MAX * L3G_RANGE;
|
|
int16_t gyroYRaw = rxBuffer[11] << 8 | rxBuffer[12];
|
|
float gyroY = static_cast<float>(gyroYRaw) / INT16_MAX * L3G_RANGE;
|
|
int16_t gyroZRaw = rxBuffer[13] << 8 | rxBuffer[14];
|
|
float gyroZ = static_cast<float>(gyroZRaw) / INT16_MAX * L3G_RANGE;
|
|
sif::printInfo("Status register: 0b" BYTE_TO_BINARY_PATTERN "\n", BYTE_TO_BINARY(statusReg));
|
|
sif::printInfo("Gyro X: %f\n", gyroX);
|
|
sif::printInfo("Gyro Y: %f\n", gyroY);
|
|
sif::printInfo("Gyro Z: %f\n", gyroZ);
|
|
}
|
|
|
|
|
|
void GyroL3GD20H::spiTransferCompleteCallback(SPI_HandleTypeDef *hspi, void* args) {
|
|
transferState = TransferStates::SUCCESS;
|
|
HAL_GPIO_WritePin(GPIOD, GPIO_PIN_14, GPIO_PIN_SET);
|
|
if(GyroL3GD20H::transferMode == spi::TransferModes::DMA) {
|
|
// Invalidate cache prior to access by CPU
|
|
SCB_InvalidateDCache_by_Addr ((uint32_t *)GyroL3GD20H::rxBuffer.data(),
|
|
GyroL3GD20H::recvBufferSize);
|
|
}
|
|
}
|
|
|
|
/**
|
|
* @brief SPI error callbacks.
|
|
* @param hspi: SPI handle
|
|
* @note This example shows a simple way to report transfer error, and you can
|
|
* add your own implementation.
|
|
* @retval None
|
|
*/
|
|
void GyroL3GD20H::spiTransferErrorCallback(SPI_HandleTypeDef *hspi, void* args) {
|
|
transferState = TransferStates::FAILURE;
|
|
}
|