67 lines
2.0 KiB
Rust
67 lines
2.0 KiB
Rust
//! ADXL343 accelerometer example
|
|
//!
|
|
//! Please note that the default REB1 board is not populated with the ADXL343BCCZ-RL7.
|
|
//! To use this example, this chip needs to be soldered onto the board.
|
|
#![no_main]
|
|
#![no_std]
|
|
use cortex_m_rt::entry;
|
|
use embedded_hal::delay::DelayNs;
|
|
use embedded_hal::spi::{SpiBus, MODE_3};
|
|
use panic_rtt_target as _;
|
|
use rtt_target::{rprintln, rtt_init_print};
|
|
use va108xx_hal::gpio::{Output, PinState};
|
|
use va108xx_hal::pins::PinsA;
|
|
use va108xx_hal::spi::{configure_pin_as_hw_cs_pin, SpiClkConfig};
|
|
use va108xx_hal::timer::CountdownTimer;
|
|
use va108xx_hal::{
|
|
pac,
|
|
prelude::*,
|
|
spi::{Spi, SpiConfig},
|
|
};
|
|
|
|
const READ_MASK: u8 = 1 << 7;
|
|
const _MULTI_BYTE_MASK: u8 = 1 << 6;
|
|
const DEVID_REG: u8 = 0x00;
|
|
|
|
const POWER_CTL_REG: u8 = 0x2D;
|
|
const PWR_MEASUREMENT_MODE_MASK: u8 = 1 << 3;
|
|
|
|
#[entry]
|
|
fn main() -> ! {
|
|
rtt_init_print!();
|
|
rprintln!("-- Vorago Accelerometer Example --");
|
|
let dp = pac::Peripherals::take().unwrap();
|
|
let pinsa = PinsA::new(dp.porta);
|
|
let mut delay = CountdownTimer::new(50.MHz(), dp.tim0);
|
|
let (sck, mosi, miso) = (pinsa.pa20, pinsa.pa19, pinsa.pa18);
|
|
let cs_pin = pinsa.pa16;
|
|
let hw_cs_id = configure_pin_as_hw_cs_pin(cs_pin);
|
|
|
|
// Need to set the ADC chip select low
|
|
Output::new(pinsa.pa17, PinState::Low);
|
|
|
|
let spi_cfg = SpiConfig::default()
|
|
.clk_cfg(
|
|
SpiClkConfig::from_clk(50.MHz(), 1.MHz()).expect("creating SPI clock config failed"),
|
|
)
|
|
.mode(MODE_3)
|
|
.slave_output_disable(true);
|
|
let mut spi = Spi::new(50.MHz(), dp.spib, (sck, miso, mosi), spi_cfg).unwrap();
|
|
spi.cfg_hw_cs(hw_cs_id);
|
|
|
|
let mut tx_rx_buf: [u8; 3] = [0; 3];
|
|
tx_rx_buf[0] = READ_MASK | DEVID_REG;
|
|
spi.transfer_in_place(&mut tx_rx_buf[0..2])
|
|
.expect("Reading DEVID register failed");
|
|
rprintln!("DEVID register: {}", tx_rx_buf[1]);
|
|
|
|
tx_rx_buf[0] = POWER_CTL_REG;
|
|
tx_rx_buf[1] = PWR_MEASUREMENT_MODE_MASK;
|
|
spi.write(&tx_rx_buf[0..2])
|
|
.expect("Enabling measurement mode failed");
|
|
|
|
loop {
|
|
delay.delay_ms(500);
|
|
}
|
|
}
|