90 lines
2.4 KiB
Rust
90 lines
2.4 KiB
Rust
|
//! ADXL343 accelerometer example
|
||
|
//!
|
||
|
//! Please note that the default REB1 board is not populated with the ADXL343BCCZ-RL7.
|
||
|
//! To use this example, this chip needs to be soldered onto the board.
|
||
|
#![no_main]
|
||
|
#![no_std]
|
||
|
use cortex_m_rt::entry;
|
||
|
use embedded_hal::spi;
|
||
|
use panic_rtt_target as _;
|
||
|
use rtt_target::{rprintln, rtt_init_print};
|
||
|
use va108xx_hal::{
|
||
|
gpio::PinsA,
|
||
|
pac::{self, interrupt},
|
||
|
prelude::*,
|
||
|
spi::{Spi, SpiConfig, TransferConfig},
|
||
|
timer::{default_ms_irq_handler, set_up_ms_timer, Delay},
|
||
|
};
|
||
|
|
||
|
const READ_MASK: u8 = 1 << 7;
|
||
|
const _MULTI_BYTE_MASK: u8 = 1 << 6;
|
||
|
const DEVID_REG: u8 = 0x00;
|
||
|
|
||
|
const POWER_CTL_REG: u8 = 0x2D;
|
||
|
const PWR_MEASUREMENT_MODE_MASK: u8 = 1 << 3;
|
||
|
|
||
|
#[entry]
|
||
|
fn main() -> ! {
|
||
|
rtt_init_print!();
|
||
|
rprintln!("-- Vorago Accelerometer Example --");
|
||
|
let mut dp = pac::Peripherals::take().unwrap();
|
||
|
let tim0 = set_up_ms_timer(
|
||
|
&mut dp.SYSCONFIG,
|
||
|
&mut dp.IRQSEL,
|
||
|
50.mhz().into(),
|
||
|
dp.TIM0,
|
||
|
interrupt::OC0,
|
||
|
);
|
||
|
let mut delay = Delay::new(tim0);
|
||
|
unsafe {
|
||
|
cortex_m::peripheral::NVIC::unmask(pac::Interrupt::OC0);
|
||
|
}
|
||
|
|
||
|
let pinsa = PinsA::new(&mut dp.SYSCONFIG, None, dp.PORTA);
|
||
|
let spi_cfg = SpiConfig::default();
|
||
|
let (sck, mosi, miso) = (
|
||
|
pinsa.pa20.into_funsel_2(),
|
||
|
pinsa.pa19.into_funsel_2(),
|
||
|
pinsa.pa18.into_funsel_2(),
|
||
|
);
|
||
|
let cs_pin = pinsa.pa16.into_funsel_2();
|
||
|
|
||
|
// Need to set the ADC chip select low
|
||
|
let mut adc_cs = pinsa.pa17.into_push_pull_output();
|
||
|
adc_cs
|
||
|
.set_high()
|
||
|
.expect("Setting ADC chip select high failed");
|
||
|
|
||
|
let transfer_cfg = TransferConfig::new(1.mhz(), spi::MODE_3, Some(cs_pin), false, true);
|
||
|
let mut spi = Spi::spib(
|
||
|
dp.SPIB,
|
||
|
(sck, miso, mosi),
|
||
|
50.mhz(),
|
||
|
spi_cfg,
|
||
|
Some(&mut dp.SYSCONFIG),
|
||
|
Some(&transfer_cfg.downgrade()),
|
||
|
);
|
||
|
|
||
|
let mut send_buf: [u8; 3] = [0; 3];
|
||
|
send_buf[0] = READ_MASK | DEVID_REG;
|
||
|
let reply = spi
|
||
|
.transfer(&mut send_buf[0..2])
|
||
|
.expect("Reading DEVID register failed");
|
||
|
rprintln!("DEVID register: {}", reply[1]);
|
||
|
|
||
|
send_buf[0] = POWER_CTL_REG;
|
||
|
send_buf[1] = PWR_MEASUREMENT_MODE_MASK;
|
||
|
spi.write(&send_buf[0..2])
|
||
|
.expect("Enabling measurement mode failed");
|
||
|
|
||
|
loop {
|
||
|
delay.delay_ms(500);
|
||
|
todo!("Not implemented for now, is not populated on the board..");
|
||
|
}
|
||
|
}
|
||
|
|
||
|
#[interrupt]
|
||
|
fn OC0() {
|
||
|
default_ms_irq_handler();
|
||
|
}
|