fsfw_example_public/doc/README-bbb.md

_{^{Image taken from Beagle Bone website and used in accordance to their trademark rules.}}

Getting started on the Beagle Bone Black

The FSFW can be run on a Beagle Bone Black with the Linux OSAL, using an ARM linux (cross) compiler. Instructions will be provided on how to do this.

General Information

The following instructions will show how to build the example on the Beagle Bone Black directly. It will also show how to cross-compile on a host machine and mirror the Beagle Bone sysroot folder on the host machine so that the same libraries and headers used on the BBB are used for the cross-compilation process.

Some Eclipse project files were provided as well to help with setting up the indexer in Eclipse more quickly.

Prerequisites for direct compilation and cross-compiling

1. SSH connection to the Beagle Bone Black working
2. Beagle Bone Black linux environment set up properly
3. CMake installed

Setting up general prerequisites for Linux systems

1. Install CMake and rsync

   sudo apt-get install cmake rsync
   

2. Configure the Beagle Bone Black Linux environment. The last section of the Linux README specifies how to set up a UNIX environment for the FSFW and is also applicable to the Beagle Bone Black. SSH into the BBB and follow the instructions in that section.

3. Install the gpiod library

   sudo apt-get install gpiod libgpiod-dev
   

Getting started on the Beagle Bone Black

Make sure to follow the steps above. Now you should be able to build the software on the Beagle Bone Black. A ssh connection to the Raspberry Pi is assumed here

You can build the software with the following commands

mkdir build-Debug-BBB
cd build-Debug-BBB
cmake -DOS_FSFW=linux -DTGT_BSP=arm/beagleboneblack -DLINUX_CROSS_COMPILE=OFF -DCMAKE_BUILD_TYPE=Debug ..
cmake --build . -j2

Prerequisites for cross-compiling

These prerequisites are valid for Linux as well as Windows hosts.

1. ARM Linux cross compiler installed
2. Beagle Bone Black sysroot folder mirrored on the host machine, using rsync
3. gdb-multiarch installed on host for remote debugging or tcf-agent running on the BBB

Cross-Compiling on a Linux Host

Setting up prerequisites for cross-compiling

Cross-Compiling on a Windows Host

Additional Prerequites

1. MSYS2 installed. All command line steps shown here were performed in the MSYS2 MinGW64 shell (not the default MSYS2, use MinGW64!). Replace <UserName> with respectively. It is recommended to set up aliases in the .bashrc file to allow quick navigation to the fsfw_example repository and to run git config --global core.autocrlf true for git in MinGW64.

Setting up prerequisites for Windows

1. Install CMake and rsync in MinGW64 after installing MSYS2

   pacman -S mingw-w64-x86_64-cmake rsync
   

2. Configure the Beagle Bone Black linux environment. The last section of the Linux REAMDE specifies how to set up a UNIX environment for the FSFW and isalso applicable to the Raspberry Pi. SSH into the Beagle Bone Black and follow the instructions in that section.

3. Install the correct ARM Linux cross-compile toolchain. provided by Linaro.

   Test the toolchain by running:

   arm-linux-gnueabihf-gcc --version
   

4. Set up a sysroot folder on the local host machine. Make sure the SSH connection to the Raspberry Pi is working without issues. Then perform the following steps

   cd /c/Users/<UserName>
   mkdir beaglebone
   cd beaglebone
   mkdir rootfs
   cd rootfs
   pwd
   

   Store the result of pwd, it is going to be used by rsync later.

   Now use rsync to clone the Rapsberry Pi sysroot to the local host machine. You can replace <ip-address> with beaglebone.local to use DNS. Use the rootfs location stored from the previous steps as <rootfs-path>.

   rsync -vR --progress -rl --delete-after --safe-links <username>@<ip-address>:/{lib,usr,opt/vc/lib} <rootfs-path>
   

5. There might be some issues with the pthread symbolic links. Navigate to the folder containing the symlinks

   cd /c/User/<UserName>/beaglebone/rootfs/usr/lib/arm-linux-gnueabihf
   

   Type more libpthread, press TAB and check whether the symbolic link libpthread.so is shown. If it is not, we are going to set it up manually to avoid issues when linking against pthread later.

   Run the following command to create a symlink to libpthread.so.0

   ln -s ../../../lib/arm-linux-gnueabihf/libpthread.so.0 libpthread.so 
   

   Please note that there might also be issues with some symlinks or libraries not being copied properly. This has occured with files like libc.so.6. If there are linker issues at a later stage, you can try to rerun rsync without --safe-links or copy the shared libraries or symlinks manually from the Raspberry Pi to the sysroot with scp.

   For example, you can copy libc.so.6 from the Raspberry Pi to the sysroot with the following command

   scp pi@<ip-address>:lib/arm-linux-gnueabihf/lib.so.6 <rootfs-path>/lib/arm-linux-gnueabihf
   

6. It is recommended to install gdb-multiarch. This tool will allow remote debugging on the host computer. Replace x86_64 with the correct processor architecture for other architectures.

   pacman -S mingw-w64-x86_64-gdb-multiarch
   

7. Perform the steps in the following chapter to build the software for the Raspberry Pi and test it.

Testing the cross-compilation

It is recommended to set the following environmental variables for the CMake build:

• CROSS_COMPILE: Explicitely specify the name of the cross compiler
• BBB_ROOTFS: Explicitely set the path to the local BBB rootfs

For example with the following commands

export CROSS_COMPILE="arm-linux-gnueabihf"

It is recommended to test whether the environmental variables were set correctly, for example by running

echo $BBB_ROOTFS

These variables can either be set every time before a debugging session to keep the environment clean (should be done before starting Eclipse) or permanently by adding the export commands to system files.

A helper script has been provided in cmake/scripts/BBB to perform setting up the environment. The scripts need to be sourced instead of being run like regular shell scripts.

You can also set up the environmental variables permanently by adding the export commands to the .profile or .bashrc file in the $HOME folder. On Windows, MinGW64 was used to set up the build system, so you can use the MinGW64 .bashrc file to do this. If you are using Eclipse to build the software, Eclipse will have the system variables from Windows, so it is recommended to either permanently set the three environmental variables in the Windows system environmental variables or add them in Eclipse. See the Eclipse README for more information.

Now we can test whether everything was set up properly by compiling the example and running it on the BBB via command line. Navigate into the fsfw_example folder first.

1. Build the software locally to test the cross-compilation process. A debug build directory is created first.

   mkdir build-Debug-BBB
   cd build-Debug-BBB
   

2. Configure the build system. On Linux, run the following command:

   cmake -G "Unix Makefiles" -DOS_FSFW=linux -DTGT_BSP=arm/beagleboneblack -DLINUX_CROSS_COMPILE=ON -DCMAKE_BUILD_TYPE=Debug ..
   

   On Windows, replace -G "Unix Makefiles" with -G "MinGW Makefiles".

   Alternatively, you can use the helper shell scripts located inside cmake/scripts/BBB/crosscompile or the Python helper script cmake_build_config.py inside the cmake/scripts folder. The BBB folder also contains template shell files which can be sourced to quickly set up the environmental variables if you want to keep the system path clean.

3. Run the binary to test it

   scp fsfw_example <username>@beaglebone.local:/home/fsfw_example
   ssh <username>@beaglebone.local
   ./fsfw_example
   

Setting up Eclipse for a BBB remote target

It is recommended to use the provided Eclipse project files and launch configurations to have a starting point. See the specific section in the Eclipse README for information how to do this.

Windows

There are some additional steps necessary on Windows: The cross-compiler by default is configured to look for the cross-compiler in /opt/cross-pi-gcc/bin. The toolchain path needs to be corrected, for example like shown in the following image:

Setting up the TCF agent on the BBB

It is recommended to set up a TCF agent for comfortable Eclipse remote debugging. The following steps show how to setup the TCF agent on the Raspberry Pi and add it to the auto-startup applications. The steps are taken from this guide

1. Install required packages on the RPi

   sudo apt-get install git uuid uuid-dev libssl-dev
   

2. Clone the repository and perform some preparation steps

   git clone git://git.eclipse.org/gitroot/tcf/org.eclipse.tcf.agent.git
   cd org.eclipse.tcf.agent.git/agent
   

3. Build the TCF agent

   make
   

   and then test it by running

   obj/GNU/Linux/arm/Debug/agent –S
   

4. Finally install the agent for auto-start with the following steps. And set it up for auto-start.

   cd org.eclipse.tcf.agent/agent
   make install
   sudo make install INSTALLROOT=
   sudo update-rc.d tcf-agent defaults
   

The Eclipse README specifies how to perform remote debugging using the TCF agent.