76 lines
2.8 KiB
Markdown
76 lines
2.8 KiB
Markdown
sat-rs example for the STM32F3-Discovery board
|
|
=======
|
|
|
|
This example application shows how the [sat-rs framework](https://egit.irs.uni-stuttgart.de/rust/satrs-launchpad)
|
|
can be used on an embedded target. It also shows how a relatively simple OBSW could be built when no
|
|
standard runtime is available. It uses [RTIC](https://rtic.rs/1/book/en/) as the concurrency
|
|
framework.
|
|
|
|
The STM32F3-Discovery device was picked because it is a cheap Cortex-M4 based device which is also
|
|
used by the [Rust Embedded Book](https://docs.rust-embedded.org/book/intro/hardware.html) and the
|
|
[Rust Discovery](https://docs.rust-embedded.org/discovery/f3discovery/) book as an introduction
|
|
to embedded Rust.
|
|
|
|
## Preparing Rust and the repository
|
|
|
|
Building an application requires the `thumbv7em-none-eabihf` cross-compiler toolchain.
|
|
If you have not installed it yet, you can do so with
|
|
|
|
```sh
|
|
rustup target add thumbv7em-none-eabihf
|
|
```
|
|
|
|
A default `.cargo` config file is provided for this project, but needs to be copied to have
|
|
the correct name. This is so that the config file can be updated or edited for custom needs
|
|
without being tracked by git.
|
|
|
|
```sh
|
|
cp def_config.toml config.toml
|
|
```
|
|
|
|
The configuration file will also set the target so it does not always have to be specified with
|
|
the `--target` argument.
|
|
|
|
## Building
|
|
|
|
After that, assuming that you have a `.cargo/config.toml` setting the correct build target,
|
|
you can simply build the application with
|
|
|
|
```sh
|
|
cargo build
|
|
```
|
|
|
|
## Flashing and Debugging from the command line
|
|
|
|
TODO
|
|
|
|
## Debugging with VS Code
|
|
|
|
The STM32F3-Discovery comes with an on-board ST-Link so all that is required to flash and debug
|
|
the board is a Mini-USB cable. The code in this repository was debugged using `openocd`
|
|
and the VS Code [`Cortex-Debug` plugin](https://marketplace.visualstudio.com/items?itemName=marus25.cortex-debug).
|
|
|
|
Some sample configuration files for VS Code were provided as well. You can simply use `Run` and `Debug`
|
|
to automatically rebuild and flash your application.
|
|
|
|
The `tasks.json` and `launch.json` files are generic and you can use them immediately by opening
|
|
the folder in VS code or adding it to a workspace.
|
|
|
|
If you would like to use a custom GDB application, you can specify the gdb binary in the following
|
|
configuration variables in your `settings.json`:
|
|
|
|
- `"cortex-debug.gdbPath"`
|
|
- `"cortex-debug.gdbPath.linux"`
|
|
- `"cortex-debug.gdbPath.windows"`
|
|
- `"cortex-debug.gdbPath.osx"`
|
|
|
|
## Commanding with Python
|
|
|
|
When the SW is running on the Discovery board, you can command the MCU via a serial interface,
|
|
using COBS encoded CCSDS packets.
|
|
|
|
TODO:
|
|
- How and where to connect serial interface on the MCU
|
|
- How to set up Python venv (or at least strongly recommend it) and install deps
|
|
- How to copy `def_tmtc_conf.json` to `tmtc_conf.json` and adapt it for custom serial port
|