fsfw_example_public/doc/README-rpi.md

_{^{Image taken from Raspberry Pi website. Raspberry Pi is a trademark of the Raspberry Pi Foundation}}

Getting started on the Raspberry Pi

The FSFW can be run on a Raspberry Pi with the Linux OSAL, using an ARM linux (cross) compiler. Instructions will be provided on how to do this.

General Information

The following instructions will show how to build the example on the Raspberry Pi directly. It will also show how to cross-compile on a host machine and mirror the Raspberry Pi sysroot folder on the host machine so that the same libraries and headers used on the RPi are used for the cross-compilation process.

Some Eclipse project files were provided as well to help with setting up the indexer in Eclipse more quickly.

Prerequisites for direct compilation and cross-compiling

1. SSH connection to the Raspberry Pi working
2. Raspberry Pi linux environment set up properly
3. CMake installed

Setting up general prerequisites for Linux systems

1. Install CMake and rsync

   sudo apt-get install cmake rsync
   

2. Configure the Raspberry Pi Linux environment. The last section of the Linux README specifies how to set up a UNIX environment for the FSFW and is also applicable to the Raspberry Pi. SSH into the Raspberry Pi and follow the instructions in that section.

3. Install the gpiod library

   sudo apt-get install gpiod libgpiod-dev
   

Getting started on the Raspberry Pi

Make sure to follow the steps above. Now you should be able to build the software on the Raspberry Pi. A ssh connection to the Raspberry Pi is assumed here

You can build the software with the following commands

mkdir build-Debug-RPi
cd build-Debug-RPi
cmake -DOS_FSFW=linux -DTGT_BSP=arm/raspberrypi -DLINUX_CROSS_COMPILE=OFF -DCMAKE_BUILD_TYPE=Debug ..
cmake --build . -j

Prerequisites for cross-compiling

These prerequisites are valid for Linux as well as Windows hosts.

1. ARM Linux cross compiler installed
2. Raspberry Pi sysroot folder mirrored on the host machine, using rsync
3. gdb-multiarch installed on host for remote debugging or tcf-agent running on Raspberry Pi

Cross-Compiling on a Linux Host

Steps tested for Ubuntu 20.04. Adapt accordingly for used Linux distribution. The following steps are based on this stackoverflow post. For the steps show here, we are also going to assume that a new Raspbian image based on Debian buster is used. If this is not the case, it is recommended to follow the steps in the stackoverflow post above and to make sure that the toolchain binaries are added to the path accordingly.

Setting up prerequisites for cross-compiling

1. Install the pre-built ARM cross-compile with the following command

   wget https://github.com/Pro/raspi-toolchain/releases/latest/download/raspi-toolchain.tar.gz
   

   Please note that this version of the toolchain might become obsolete in the future. If another toolchain installation is used, it is still recommended to unpack the toolchain in the /opt/cross-pi-gcc folder so that the Eclipse configuration and helper scripts work without adaptions. Add the folder to the system path. On Linux, this can generally be done with the following command

   export PATH=$PATH:"/opt/cross-pi-gcc/bin"
   

   You can add this line to the .bashrc or .profile file in the $HOME directory to add environmental variables permanently. More experienced users can perform this step is a shell script which is sourced to keep the environment clean.

   Test the toolchain with the following command

   arm-linux-gnueabihf-gcc --version
   

2. Set up a sysroot folder on the local host machine. Make sure the SSH connection to the Raspberry Pi is working without issues. Then perform the following steps

   cd ~
   mkdir raspberrypi
   cd raspberrypi
   mkdir rootfs
   cd rootfs 
   pwd
   

   The result of the pwd command will be used later to sync the root file system of the Raspberry Pi to the host machine. With a Raspberry Pi 4, you can replace <ip-address> with raspberrypi.local and when using the default rootfs path, you can replace <rootfs-path> with $HOME/raspberrypi/rootfs.

   rsync -vR --progress -rl --delete-after --safe-links pi@<ip-address>:/{lib,usr,opt/vc/lib} <rootfs-path>
   

   Please note that rsync sometimes does not copy shared libraries or symlinks properly, which might result in errors when cross-compiling and cross-linking. See the troubleshooting section for more details.

3. It is recommended to install gdb-multiarch. This tool will allow remote debugging on the host computer. This step is not required if the tcf-agent is used.

   sudo apt-get install gdb-multiarch
   

4. Perform the steps in the cross-compile section to build the software for the Raspberry Pi and test it.

Cross-Compiling on a Windows Host

Additional Prerequites

1. MSYS2 installed. All command line steps shown here were performed in the MSYS2 MinGW64 shell (not the default MSYS2, use MinGW64!). Replace <UserName> with respectively. It is recommended to set up aliases in the .bashrc file to allow quick navigation to the fsfw_example repository and to run git config --global core.autocrlf true for git in MinGW64.

Setting up prerequisites for Windows

1. Install CMake and rsync in MinGW64 after installing MSYS2

   pacman -S mingw-w64-x86_64-cmake rsync
   

2. Configure the Raspberry Pi linux environment. The last section of the Linux REAMDE specifies how to set up a UNIX environment for the FSFW and isalso applicable to the Raspberry Pi. SSH into the Raspberry Pi and follow the instructions in that section.

3. Install the correct ARM Linux cross-compile toolchain provided by SysProgs. You can find out the distribution release of your Raspberry Pi by running cat /etc/rpi-issue.

   Test the toolchain by running:

   arm-linux-gnueabihf-gcc --version
   

4. Set up a sysroot folder on the local host machine. Make sure the SSH connection to the Raspberry Pi is working without issues. Then perform the following steps

   cd /c/Users/<UserName>
   mkdir raspberrypi
   cd raspberrypi
   mkdir rootfs
   cd rootfs
   pwd
   

   Store the result of pwd, it is going to be used by rsync later.

   Now use rsync to clone the Rapsberry Pi sysroot to the local host machine. With a Raspberry Pi 4, you can replace <ip-address> with raspberrypi.local. Use the rootfs location stored from the previous steps as <rootfs-path>.

   rsync -vR --progress -rl --delete-after --safe-links pi@<ip-address>:/{lib,usr,opt/vc/lib} <rootfs-path>
   

   Please note that rsync sometimes does not copy shared libraries or symlinks properly, which might result in errors when cross-compiling and cross-linking. See the troubleshooting section for more details.

5. It is recommended to install gdb-multiarch. This tool will allow remote debugging on the host computer. Replace x86_64 with the correct processor architecture for other architectures. This is not required if the tcf-agent is used.

   pacman -S mingw-w64-x86_64-gdb-multiarch
   

6. Perform the steps in the following chapter to build the software for the Raspberry Pi and test it.

Testing the cross-compilation

It is recommended to set the following environmental variables for the CMake build:

• CROSS_COMPILE: Explicitely specify the name of the cross compiler
• RASPBERRY_VERSION: Explicitely specify the version of the Raspberry Pi
• RASPBIAN_ROOTFS: Explicitely set the path to the local RPi rootfs

For example with the following commands

export CROSS_COMPILE="arm-linux-gnueabihf"
export RASPBERRY_VERSION="4"
export RASPBIAN_ROOTFS="<pathToRootFS>"

It is recommended to test whether the environmental variables were set correctly, for example by running

echo $RASPBIAN_ROOTFS

These variables can either be set every time before a debugging session to keep the environment clean (should be done before starting Eclipse) or permanently by adding the export commands to system files.

A helper script has been provided in cmake/scripts/RPi to perform setting up the environment. The scripts need to be sourced instead of being run like regular shell scripts.

You can also set up the environmental variables permanently by adding the export commands to the .profile or .bashrc file in the $HOME folder. On Windows, MinGW64 was used to set up the build system, so you can use the MinGW64 .bashrc file to do this. If you are using Eclipse to build the software, Eclipse will have the system variables from Windows, so it is recommended to either permanently set the three environmental variables in the Windows system environmental variables or add them in Eclipse. See the Eclipse README for more information.

Now we can test whether everything was set up properly by compiling the example and running it on the Raspberry Pi via command line. Navigate into the fsfw_example folder first.

1. Build the software locally to test the cross-compilation process. We are going to create a Debug build directory first.

   mkdir build-Debug-RPi
   cd build-Debug-RPi
   

2. Configure the build system. On Linux, run the following command:

   cmake -G "Unix Makefiles" -DOS_FSFW=linux -DTGT_BSP=arm/raspberrypi -DLINUX_CROSS_COMPILE=ON -DCMAKE_BUILD_TYPE=Debug ..
   

   On Windows, replace -G "Unix Makefiles" with -G "MinGW Makefiles".

   Alternatively, you can use the helper shell scripts located inside cmake/scripts/RPi/crosscompile or the Python helper script cmake_build_config.py inside the cmake/scripts folder. The RPi folder also contains template shell files which can be sourced to quickly set up the environmental variables if you want to keep the system path clean.

3. Run the binary to test it

   scp fsfw_example pi@raspberrypi.local:/home/pi/fsfw_example
   ssh pi@raspberrypi.local
   ./fsfw_example
   

Setting up Eclipse for a Raspberry Pi remote target

It is recommended to use the provided Eclipse project files and launch configurations to have a starting point. See the specific section in the Eclipse README for information how to do this.

Windows

There are some additional steps necessary on Windows: The cross-compiler by default is configured to look for the cross-compiler in /opt/cross-pi-gcc/bin. The toolchain path needs to be corrected, for example like shown in the following image:

Setting up the TCF agent on the Raspberry Pi

It is recommended to set up a TCF agent for comfortable Eclipse remote debugging. The following steps show how to setup the TCF agent on the Raspberry Pi and add it to the auto-startup applications. The steps are taken from this guide

1. Install required packages on the RPi

   sudo apt-get install git uuid uuid-dev libssl-dev
   

2. Clone the repository and perform some preparation steps

   git clone git://git.eclipse.org/gitroot/tcf/org.eclipse.tcf.agent.git
   cd org.eclipse.tcf.agent.git/agent
   

3. Build the TCF agent

   make
   

   and then test it by running

   obj/GNU/Linux/arm/Debug/agent –S
   

4. Finally instal lthe agent for auto-start with the following steps and set it up for auto-start. The last step did not work on a Rapsberry Pi 4, but apparentely was not necessary.

   cd org.eclipse.tcf.agent/agent
   make install
   sudo make install INSTALLROOT=
   sudo update-rc.d tcf-agent defaults
   sudo update-rc.d tcf-agent enable 2
   

The Eclipse README specifies how to perform remote debugging using the TCF agent.

Troubleshooting

Cloning Sysroot

There might be some issues with the pthread symbolic links. Navigate to the folder containing the symlinks

cd /c/User/<UserName>/beaglebone/rootfs/usr/lib/arm-linux-gnueabihf

Type more libpthread, press TAB and check whether the symbolic link libpthread.so is shown. If it is not, we are going to set it up manually to avoid issues when linking against pthread later.

Run the following command to create a symlink to libpthread.so.0

ln -s ../../../lib/arm-linux-gnueabihf/libpthread.so.0 libpthread.so 

Please note that there might also be issues with some symlinks or libraries not being copied properly. This has occured with files like libc.so.6. If there are linker issues at a later stage, you can try to rerun rsync without --safe-links or copy the shared libraries or symlinks manually from the Linux board to the sysroot with scp.

For example, you can copy libc.so.6 from the Linux board to the sysroot with the following command

scp <user_name>@<ip-address>:lib/arm-linux-gnueabihf/lib.so.6 <rootfs-path>/lib/arm-linux-gnueabihf

If there are issues with the cross-compilation process, manually copying these shared libraries can help

scp <user_name>@<ip-address>:/usr/lib/arm-linux-gnueabihf/libc.so <rootfs_path>/usr/lib/arm-linux-gnueabihf
scp <user_name>@<ip-address>:/usr/lib/arm-linux-gnueabihf/libc.a <rootfs_path>/usr/lib/arm-linux-gnueabihf

scp <user_name>@<ip-address>:/usr/lib/arm-linux-gnueabihf/librt.a <rootfs_path>/usr/lib/arm-linux-gnueabihf
scp <user_name>@<ip-address>:/usr/lib/arm-linux-gnueabihf/librt.so <rootfs_path>/usr/lib/arm-linux-gnueabihf

scp <user_name>@<ip-address>:/lib/arm-linux-gnueabihf/librt.so.1 <rootfs_path>/lib/arm-linux-gnueabihf
scp <user_name>@<ip-address>:/lib/arm-linux-gnueabihf/libpthread.so.0 <rootfs_path>/lib/arm-linux-gnueabihf
scp <user_name>@<ip-address>:/lib/arm-linux-gnueabihf/ld-linux-armhf.so.3 <rootfs_path>/lib/arm-linux-gnueabihf
scp <user_name>@<ip-address>:/lib/arm-linux-gnueabihf/libc.so.6 <rootfs_path>/lib/arm-linux-gnueabihf