- Reset reply size after returning a reply
- Reset data link layer and flush RX for regular commands and before
performing special commands to ensure consistent start state
- Clean up DHB a bit
- Set STR dev to OFF in assembly when it is faulty.
11300;0x2c24;SWITCH_CMD_SENT;INFO;Indicates that a FSFW object requested setting a switch P1: 1 if on was requested, 0 for off | P2: Switch Index;mission/devices/devicedefinitions/powerDefinitions.h
11301;0x2c25;SWITCH_HAS_CHANGED;INFO;Indicated that a switch state has changed P1: New switch state, 1 for on, 0 for off | P2: Switch Index;mission/devices/devicedefinitions/powerDefinitions.h
11601;0x2d51;MEMORY_READ_RPT_CRC_FAILURE;LOW;PLOC crc failure in telemetry packet;linux/devices/ploc/PlocMPSoCHandler.h
11602;0x2d52;ACK_FAILURE;LOW;PLOC receive acknowledgment failure report P1: Command Id which leads the acknowledgment failure report P2: The status field inserted by the MPSoC into the data field;linux/devices/ploc/PlocMPSoCHandler.h
11603;0x2d53;EXE_FAILURE;LOW;PLOC receive execution failure report P1: Command Id which leads the execution failure report P2: The status field inserted by the MPSoC into the data field;linux/devices/ploc/PlocMPSoCHandler.h
11604;0x2d54;MPSOC_HANDLER_CRC_FAILURE;LOW;PLOC reply has invalid crc;linux/devices/ploc/PlocMPSoCHandler.h
11605;0x2d55;MPSOC_HANDLER_SEQUENCE_COUNT_MISMATCH;LOW;Packet sequence count in received space packet does not match expected count P1: Expected sequence count P2: Received sequence count;linux/devices/ploc/PlocMPSoCHandler.h
11606;0x2d56;MPSOC_SHUTDOWN_FAILED;HIGH;Supervisor fails to shutdown MPSoC. Requires to power off the PLOC and thus also to shutdown the supervisor.;linux/devices/ploc/PlocMPSoCHandler.h
11200;0x2bc0;SAFE_RATE_VIOLATION;MEDIUM;The limits for the rotation in safe mode were violated.;mission/acs/defs.h
11201;0x2bc1;RATE_RECOVERY;MEDIUM;The system has recovered from a rate rotation violation.;mission/acs/defs.h
11202;0x2bc2;MULTIPLE_RW_INVALID;HIGH;Multiple RWs are invalid, uncommandable and therefore higher ACS modes cannot be maintained.;mission/acs/defs.h
11203;0x2bc3;MEKF_INVALID_INFO;INFO;MEKF was not able to compute a solution. P1: MEKF state on exit;mission/acs/defs.h
11204;0x2bc4;MEKF_RECOVERY;INFO;MEKF is able to compute a solution again.;mission/acs/defs.h
11205;0x2bc5;MEKF_AUTOMATIC_RESET;INFO;MEKF performed an automatic reset after detection of nonfinite values.;mission/acs/defs.h
11206;0x2bc6;PTG_CTRL_NO_ATTITUDE_INFORMATION;HIGH;For a prolonged time, no attitude information was available for the Pointing Controller. Falling back to Safe Mode.;mission/acs/defs.h
11207;0x2bc7;SAFE_MODE_CONTROLLER_FAILURE;HIGH;The ACS safe mode controller was not able to compute a solution and has failed. P1: Missing information about magnetic field, P2: Missing information about rotational rate;mission/acs/defs.h
11208;0x2bc8;TLE_TOO_OLD;INFO;The TLE for the SGP4 Propagator has become too old.;mission/acs/defs.h
11209;0x2bc9;TLE_FILE_READ_FAILED;LOW;The TLE could not be read from the filesystem.;mission/acs/defs.h
11210;0x2bca;PTG_RATE_VIOLATION;MEDIUM;The limits for the rotation in pointing mode were violated.;mission/acs/defs.h
11300;0x2c24;SWITCH_CMD_SENT;INFO;Indicates that a FSFW object requested setting a switch P1: 1 if on was requested, 0 for off | P2: Switch Index;mission/power/defs.h
11301;0x2c25;SWITCH_HAS_CHANGED;INFO;Indicated that a switch state has changed P1: New switch state, 1 for on, 0 for off | P2: Switch Index;mission/power/defs.h
11306;0x2c2a;TIMEDELTA_OUT_OF_BOUNDS;LOW;Time difference for Coulomb Counter was too large. P1: time in s * 10;mission/power/defs.h
11307;0x2c2b;POWER_LEVEL_LOW;HIGH;The State of Charge is below the limit for payload use. Setting Payload to faulty.;mission/power/defs.h
11308;0x2c2c;POWER_LEVEL_CRITICAL;HIGH;The State of Charge is below the limit for higher modes. Setting Reaction Wheels to faulty.;mission/power/defs.h
11601;0x2d51;MEMORY_READ_RPT_CRC_FAILURE;LOW;PLOC crc failure in telemetry packet;linux/payload/PlocMpsocHandler.h
11602;0x2d52;ACK_FAILURE;LOW;PLOC receive acknowledgment failure report P1: Command Id which leads the acknowledgment failure report P2: The status field inserted by the MPSoC into the data field;linux/payload/PlocMpsocHandler.h
11603;0x2d53;EXE_FAILURE;LOW;PLOC receive execution failure report P1: Command Id which leads the execution failure report P2: The status field inserted by the MPSoC into the data field;linux/payload/PlocMpsocHandler.h
11604;0x2d54;MPSOC_HANDLER_CRC_FAILURE;LOW;PLOC reply has invalid crc;linux/payload/PlocMpsocHandler.h
11605;0x2d55;MPSOC_HANDLER_SEQUENCE_COUNT_MISMATCH;LOW;Packet sequence count in received space packet does not match expected count P1: Expected sequence count P2: Received sequence count;linux/payload/PlocMpsocHandler.h
11606;0x2d56;MPSOC_SHUTDOWN_FAILED;HIGH;Supervisor fails to shutdown MPSoC. Requires to power off the PLOC and thus also to shutdown the supervisor.;linux/payload/PlocMpsocHandler.h
11607;0x2d57;SUPV_NOT_ON;LOW;SUPV not on for boot or shutdown process. P1: 0 for OFF transition, 1 for ON transition.;linux/payload/PlocMpsocHandler.h
11701;0x2db5;SELF_TEST_I2C_FAILURE;LOW;Get self test result returns I2C failure P1: Indicates on which axis the failure occurred. 0 -> INIT, 1 -> +X, 2 -> -X, 3 -> +Y, 4 -> -Y, 5 -> +Z, 6 -> -Z, 7 -> FINA;mission/acs/ImtqHandler.h
11702;0x2db6;SELF_TEST_SPI_FAILURE;LOW;Get self test result returns SPI failure. This concerns the MTM connectivity. P1: Indicates on which axis the failure occurred. 0 -> INIT, 1 -> +X, 2 -> -X, 3 -> +Y, 4 -> -Y, 5 -> +Z, 6 -> -Z, 7 -> FINA;mission/acs/ImtqHandler.h
11703;0x2db7;SELF_TEST_ADC_FAILURE;LOW;Get self test result returns failure in measurement of current and temperature. P1: Indicates on which axis the failure occurred. 0 -> INIT, 1 -> +X, 2 -> -X, 3 -> +Y, 4 -> -Y, 5 -> +Z, 6 -> -Z, 7 -> FINA;mission/acs/ImtqHandler.h
@ -130,151 +142,179 @@ Event ID (dec); Event ID (hex); Name; Severity; Description; File Path
11708;0x2dbc;INVALID_ERROR_BYTE;LOW;Received invalid error byte. This indicates an error of the communication link between IMTQ and OBC.;mission/acs/ImtqHandler.h
11801;0x2e19;ERROR_STATE;HIGH;Reaction wheel signals an error state;mission/acs/rwHelpers.h
12004;0x2ee4;SUPV_ACK_FAILURE;LOW;PLOC supervisor received acknowledgment failure report;linux/devices/ploc/PlocSupervisorHandler.h
12005;0x2ee5;SUPV_EXE_FAILURE;LOW;PLOC received execution failure report P1: ID of command for which the execution failed P2: Status code sent by the supervisor handler;linux/devices/ploc/PlocSupervisorHandler.h
12006;0x2ee6;SUPV_CRC_FAILURE_EVENT;LOW;PLOC supervisor reply has invalid crc;linux/devices/ploc/PlocSupervisorHandler.h
12007;0x2ee7;SUPV_HELPER_EXECUTING;LOW;Supervisor helper currently executing a command;linux/devices/ploc/PlocSupervisorHandler.h
12008;0x2ee8;SUPV_MPSOC_SHUTDOWN_BUILD_FAILED;LOW;Failed to build the command to shutdown the MPSoC;linux/devices/ploc/PlocSupervisorHandler.h
11901;0x2e7d;BOOTING_FIRMWARE_FAILED_EVENT;LOW;Failed to boot firmware;mission/acs/str/StarTrackerHandler.h
11902;0x2e7e;BOOTING_BOOTLOADER_FAILED_EVENT;LOW;Failed to boot star tracker into bootloader mode;mission/acs/str/StarTrackerHandler.h
11903;0x2e7f;COM_ERROR_REPLY_RECEIVED;LOW;Received COM error. P1: Communication Error ID (datasheet p32);mission/acs/str/StarTrackerHandler.h
12001;0x2ee1;SUPV_MEMORY_READ_RPT_CRC_FAILURE;LOW;PLOC supervisor crc failure in telemetry packet;linux/payload/plocSupvDefs.h
12002;0x2ee2;SUPV_UNKNOWN_TM;LOW;Unhandled event. P1: APID, P2: Service ID;linux/payload/plocSupvDefs.h
12004;0x2ee4;SUPV_ACK_FAILURE;LOW;PLOC supervisor received acknowledgment failure report;linux/payload/plocSupvDefs.h
12005;0x2ee5;SUPV_EXE_FAILURE;LOW;PLOC received execution failure report P1: ID of command for which the execution failed P2: Status code sent by the supervisor handler;linux/payload/plocSupvDefs.h
12006;0x2ee6;SUPV_CRC_FAILURE_EVENT;LOW;PLOC supervisor reply has invalid crc;linux/payload/plocSupvDefs.h
12007;0x2ee7;SUPV_HELPER_EXECUTING;LOW;Supervisor helper currently executing a command;linux/payload/plocSupvDefs.h
12008;0x2ee8;SUPV_MPSOC_SHUTDOWN_BUILD_FAILED;LOW;Failed to build the command to shutdown the MPSoC;linux/payload/plocSupvDefs.h
12009;0x2ee9;SUPV_ACK_UNKNOWN_COMMAND;LOW;Received ACK, but no related command is unknown or has not been sent by this software instance. P1: Module APID. P2: Service ID.;linux/payload/plocSupvDefs.h
12010;0x2eea;SUPV_EXE_ACK_UNKNOWN_COMMAND;LOW;Received ACK EXE, but no related command is unknown or has not been sent by this software instance. P1: Module APID. P2: Service ID.;linux/payload/plocSupvDefs.h
12300;0x300c;SEND_MRAM_DUMP_FAILED;LOW;Failed to send mram dump command to supervisor handler P1: Return value of commandAction function P2: Start address of MRAM to dump with this command;linux/devices/ploc/PlocMemoryDumper.h
12301;0x300d;MRAM_DUMP_FAILED;LOW;Received completion failure report form PLOC supervisor handler P1: MRAM start address of failing dump command;linux/devices/ploc/PlocMemoryDumper.h
12509;0x30dd;STR_HELPER_READING_REPLY_FAILED;LOW;Failed to read communication interface reply data P1: Return code of failed communication interface read call P1: Upload/download position for which the read call failed;linux/acs/startracker/StrComHandler.h
12510;0x30de;STR_HELPER_COM_ERROR;LOW;Unexpected stop of decoding sequence P1: Return code of failed communication interface read call P1: Upload/download position for which the read call failed;linux/acs/startracker/StrComHandler.h
12511;0x30df;STR_COM_REPLY_TIMEOUT;LOW;Star tracker did not send a valid reply for a certain timeout. P1: Position of upload or download packet for which the packet wa sent. P2: Timeout;linux/acs/startracker/StrComHandler.h
12513;0x30e1;STR_HELPER_DEC_ERROR;LOW;Error during decoding of received reply occurred P1: Return value of decoding function P2: Position of upload/download packet, or address of flash write/read request;linux/acs/startracker/StrComHandler.h
12514;0x30e2;POSITION_MISMATCH;LOW;Position mismatch P1: The expected position and thus the position for which the image upload/download failed;linux/acs/startracker/StrComHandler.h
12515;0x30e3;STR_HELPER_FILE_NOT_EXISTS;LOW;Specified file does not exist P1: Internal state of str helper;linux/acs/startracker/StrComHandler.h
12603;0x313b;MPSOC_HELPER_REQUESTING_REPLY_FAILED;LOW;Request receive message of communication interface failed P1: Return value returned by the communication interface requestReceiveMessage function P2: Internal state of MPSoC helper;linux/devices/ploc/PlocMPSoCHelper.h
12604;0x313c;MPSOC_HELPER_READING_REPLY_FAILED;LOW;Reading receive message of communication interface failed P1: Return value returned by the communication interface readingReceivedMessage function P2: Internal state of MPSoC helper;linux/devices/ploc/PlocMPSoCHelper.h
12605;0x313d;MPSOC_MISSING_ACK;LOW;Did not receive acknowledgment report P1: Number of bytes missing P2: Internal state of MPSoC helper;linux/devices/ploc/PlocMPSoCHelper.h
12606;0x313e;MPSOC_MISSING_EXE;LOW;Did not receive execution report P1: Number of bytes missing P2: Internal state of MPSoC helper;linux/devices/ploc/PlocMPSoCHelper.h
12607;0x313f;MPSOC_ACK_FAILURE_REPORT;LOW;Received acknowledgment failure report P1: Internal state of MPSoC;linux/devices/ploc/PlocMPSoCHelper.h
12608;0x3140;MPSOC_EXE_FAILURE_REPORT;LOW;Received execution failure report P1: Internal state of MPSoC;linux/devices/ploc/PlocMPSoCHelper.h
12609;0x3141;MPSOC_ACK_INVALID_APID;LOW;Expected acknowledgment report but received space packet with other apid P1: Apid of received space packet P2: Internal state of MPSoC;linux/devices/ploc/PlocMPSoCHelper.h
12610;0x3142;MPSOC_EXE_INVALID_APID;LOW;Expected execution report but received space packet with other apid P1: Apid of received space packet P2: Internal state of MPSoC;linux/devices/ploc/PlocMPSoCHelper.h
12611;0x3143;MPSOC_HELPER_SEQ_CNT_MISMATCH;LOW;Received sequence count does not match expected sequence count P1: Expected sequence count P2: Received sequence count;linux/devices/ploc/PlocMPSoCHelper.h
12700;0x319c;TRANSITION_BACK_TO_OFF;MEDIUM;Could not transition properly and went back to ALL OFF;mission/devices/PayloadPcduHandler.h
12701;0x319d;NEG_V_OUT_OF_BOUNDS;MEDIUM;P1: 0 -> too low, 1 -> too high P2: Float value;mission/devices/PayloadPcduHandler.h
12702;0x319e;U_DRO_OUT_OF_BOUNDS;MEDIUM;P1: 0 -> too low, 1 -> too high P2: Float value;mission/devices/PayloadPcduHandler.h
12703;0x319f;I_DRO_OUT_OF_BOUNDS;MEDIUM;P1: 0 -> too low, 1 -> too high P2: Float value;mission/devices/PayloadPcduHandler.h
12704;0x31a0;U_X8_OUT_OF_BOUNDS;MEDIUM;P1: 0 -> too low, 1 -> too high P2: Float value;mission/devices/PayloadPcduHandler.h
12705;0x31a1;I_X8_OUT_OF_BOUNDS;MEDIUM;P1: 0 -> too low, 1 -> too high P2: Float value;mission/devices/PayloadPcduHandler.h
12706;0x31a2;U_TX_OUT_OF_BOUNDS;MEDIUM;P1: 0 -> too low, 1 -> too high P2: Float value;mission/devices/PayloadPcduHandler.h
12707;0x31a3;I_TX_OUT_OF_BOUNDS;MEDIUM;P1: 0 -> too low, 1 -> too high P2: Float value;mission/devices/PayloadPcduHandler.h
12708;0x31a4;U_MPA_OUT_OF_BOUNDS;MEDIUM;P1: 0 -> too low, 1 -> too high P2: Float value;mission/devices/PayloadPcduHandler.h
12709;0x31a5;I_MPA_OUT_OF_BOUNDS;MEDIUM;P1: 0 -> too low, 1 -> too high P2: Float value;mission/devices/PayloadPcduHandler.h
12710;0x31a6;U_HPA_OUT_OF_BOUNDS;MEDIUM;P1: 0 -> too low, 1 -> too high P2: Float value;mission/devices/PayloadPcduHandler.h
12711;0x31a7;I_HPA_OUT_OF_BOUNDS;MEDIUM;P1: 0 -> too low, 1 -> too high P2: Float value;mission/devices/PayloadPcduHandler.h
12300;0x300c;SEND_MRAM_DUMP_FAILED;LOW;Failed to send mram dump command to supervisor handler P1: Return value of commandAction function P2: Start address of MRAM to dump with this command;linux/payload/PlocMemoryDumper.h
12301;0x300d;MRAM_DUMP_FAILED;LOW;Received completion failure report form PLOC supervisor handler P1: MRAM start address of failing dump command;linux/payload/PlocMemoryDumper.h
12410;0x307a;PDEC_TRYING_RESET_WITH_INIT;LOW;Trying a PDEC reset with complete re-initialization;linux/ipcore/pdec.h
12411;0x307b;PDEC_TRYING_RESET_NO_INIT;LOW;Trying a PDEC reset without re-initialization.;linux/ipcore/pdec.h
12412;0x307c;PDEC_RESET_FAILED;HIGH;Failed to pull PDEC reset to low;linux/ipcore/pdec.h
12413;0x307d;OPEN_IRQ_FILE_FAILED;HIGH;Failed to open the IRQ uio file;linux/ipcore/pdec.h
12414;0x307e;PDEC_INIT_FAILED;HIGH;PDEC initialization failed. This might also be due to the persistent confiuration never becoming available, for example due to SD card issues.;linux/ipcore/pdec.h
12415;0x307f;PDEC_CONFIG_CORRUPTED;HIGH;The PDEC configuration area has been corrupted P1: The first configuration word P2: The second configuration word;linux/ipcore/pdec.h
12509;0x30dd;STR_HELPER_READING_REPLY_FAILED;LOW;Failed to read communication interface reply data P1: Return code of failed communication interface read call P1: Upload/download position for which the read call failed;linux/acs/StrComHandler.h
12510;0x30de;STR_HELPER_COM_ERROR;LOW;Unexpected stop of decoding sequence P1: Return code of failed communication interface read call P1: Upload/download position for which the read call failed;linux/acs/StrComHandler.h
12511;0x30df;STR_COM_REPLY_TIMEOUT;LOW;Star tracker did not send a valid reply for a certain timeout. P1: Position of upload or download packet for which the packet wa sent. P2: Timeout;linux/acs/StrComHandler.h
12513;0x30e1;STR_HELPER_DEC_ERROR;LOW;Error during decoding of received reply occurred P1: Return value of decoding function P2: Position of upload/download packet, or address of flash write/read request;linux/acs/StrComHandler.h
12514;0x30e2;POSITION_MISMATCH;LOW;Position mismatch P1: The expected position and thus the position for which the image upload/download failed;linux/acs/StrComHandler.h
12515;0x30e3;STR_HELPER_FILE_NOT_EXISTS;LOW;Specified file does not exist P1: Internal state of str helper;linux/acs/StrComHandler.h
12603;0x313b;MPSOC_HELPER_REQUESTING_REPLY_FAILED;LOW;Request receive message of communication interface failed P1: Return value returned by the communication interface requestReceiveMessage function P2: Internal state of MPSoC helper;linux/payload/PlocMpsocSpecialComHelper.h
12604;0x313c;MPSOC_HELPER_READING_REPLY_FAILED;LOW;Reading receive message of communication interface failed P1: Return value returned by the communication interface readingReceivedMessage function P2: Internal state of MPSoC helper;linux/payload/PlocMpsocSpecialComHelper.h
12605;0x313d;MPSOC_MISSING_ACK;LOW;Did not receive acknowledgment report P1: Number of bytes missing P2: Internal state of MPSoC helper;linux/payload/PlocMpsocSpecialComHelper.h
12606;0x313e;MPSOC_MISSING_EXE;LOW;Did not receive execution report P1: Number of bytes missing P2: Internal state of MPSoC helper;linux/payload/PlocMpsocSpecialComHelper.h
12607;0x313f;MPSOC_ACK_FAILURE_REPORT;LOW;Received acknowledgment failure report P1: Internal state of MPSoC;linux/payload/PlocMpsocSpecialComHelper.h
12608;0x3140;MPSOC_EXE_FAILURE_REPORT;LOW;Received execution failure report P1: Internal state of MPSoC;linux/payload/PlocMpsocSpecialComHelper.h
12609;0x3141;MPSOC_ACK_INVALID_APID;LOW;Expected acknowledgment report but received space packet with other apid P1: Apid of received space packet P2: Internal state of MPSoC;linux/payload/PlocMpsocSpecialComHelper.h
12610;0x3142;MPSOC_EXE_INVALID_APID;LOW;Expected execution report but received space packet with other apid P1: Apid of received space packet P2: Internal state of MPSoC;linux/payload/PlocMpsocSpecialComHelper.h
12611;0x3143;MPSOC_HELPER_SEQ_CNT_MISMATCH;LOW;Received sequence count does not match expected sequence count P1: Expected sequence count P2: Received sequence count;linux/payload/PlocMpsocSpecialComHelper.h
12803;0x3203;SIDE_SWITCH_TRANSITION_NOT_ALLOWED;LOW;Not implemented, would increase already high complexity. Operator should instead command the assembly off first and then command the assembly on into the desired mode/submode combination;mission/system/acs/AcsBoardAssembly.h
12804;0x3204;DIRECT_TRANSITION_TO_DUAL_OTHER_GPS_FAULTY;MEDIUM;This is triggered when the assembly would have normally switched the board side, but the GPS device of the other side was marked faulty. P1: Current submode.;mission/system/acs/AcsBoardAssembly.h
12903;0x3267;SIDE_SWITCH_TRANSITION_NOT_ALLOWED;LOW;Not implemented, would increase already high complexity. Operator should instead command the assembly off first and then command the assembly on into the desired mode/submode combination;mission/system/acs/SusAssembly.h
13100;0x332c;GPS_FIX_CHANGE;INFO;Fix has changed. P1: Old fix. P2: New fix 0: Not seen, 1: No Fix, 2: 2D-Fix, 3: 3D-Fix;mission/devices/devicedefinitions/GPSDefinitions.h
13101;0x332d;CANT_GET_FIX;LOW;Could not get fix in maximum allowed time. P1: Maximum allowed time to get a fix after the GPS was switched on.;mission/devices/devicedefinitions/GPSDefinitions.h
13200;0x3390;P60_BOOT_COUNT;INFO;P60 boot count is broadcasted once at SW startup. P1: Boot count;mission/devices/P60DockHandler.h
13201;0x3391;BATT_MODE;INFO;Battery mode is broadcasted at startup. P1: Mode;mission/devices/P60DockHandler.h
13202;0x3392;BATT_MODE_CHANGED;MEDIUM;Battery mode has changed. P1: Old mode. P2: New mode;mission/devices/P60DockHandler.h
13607;0x3527;SUPV_EVENT_BUFFER_REQUEST_TERMINATED;LOW;Terminated event buffer request by command P1: Number of packets read before process was terminated;linux/devices/ploc/PlocSupvUartMan.h
13617;0x3531;SUPV_HELPER_REQUESTING_REPLY_FAILED;LOW;Request receive message of communication interface failed P1: Return value returned by the communication interface requestReceiveMessage function P2: Internal state of supervisor helper;linux/devices/ploc/PlocSupvUartMan.h
13618;0x3532;SUPV_HELPER_READING_REPLY_FAILED;LOW;Reading receive message of communication interface failed P1: Return value returned by the communication interface readingReceivedMessage function P2: Internal state of supervisor helper;linux/devices/ploc/PlocSupvUartMan.h
13619;0x3533;SUPV_MISSING_ACK;LOW;Did not receive acknowledgement report P1: Number of bytes missing P2: Internal state of MPSoC helper;linux/devices/ploc/PlocSupvUartMan.h
13620;0x3534;SUPV_MISSING_EXE;LOW;Supervisor did not receive execution report P1: Number of bytes missing P2: Internal state of supervisor helper;linux/devices/ploc/PlocSupvUartMan.h
13621;0x3535;SUPV_ACK_FAILURE_REPORT;LOW;Supervisor received acknowledgment failure report P1: Internal state of supervisor helper;linux/devices/ploc/PlocSupvUartMan.h
13623;0x3537;SUPV_ACK_INVALID_APID;LOW;Supervisor expected acknowledgment report but received space packet with other apid P1: Apid of received space packet P2: Internal state of supervisor helper;linux/devices/ploc/PlocSupvUartMan.h
13624;0x3538;SUPV_EXE_INVALID_APID;LOW;Supervisor helper expected execution report but received space packet with other apid P1: Apid of received space packet P2: Internal state of supervisor helper;linux/devices/ploc/PlocSupvUartMan.h
13625;0x3539;ACK_RECEPTION_FAILURE;LOW;Failed to receive acknowledgment report P1: Return value P2: Apid of command for which the reception of the acknowledgment report failed;linux/devices/ploc/PlocSupvUartMan.h
13626;0x353a;EXE_RECEPTION_FAILURE;LOW;Failed to receive execution report P1: Return value P2: Apid of command for which the reception of the execution report failed;linux/devices/ploc/PlocSupvUartMan.h
13627;0x353b;WRITE_MEMORY_FAILED;LOW;Update procedure failed when sending packet. P1: First byte percent, third and fourth byte Sequence Count, P2: Bytes written;linux/devices/ploc/PlocSupvUartMan.h
13630;0x353e;SUPV_UPDATE_PROGRESS;INFO;Will be triggered every 5 percent of the update progress. P1: First byte percent, third and fourth byte Sequence Count, P2: Bytes written;linux/devices/ploc/PlocSupvUartMan.h
13100;0x332c;GPS_FIX_CHANGE;INFO;Fix has changed. P1: Old fix. P2: New fix 0: Not seen, 1: No Fix, 2: 2D-Fix, 3: 3D-Fix;mission/acs/archive/GPSDefinitions.h
13101;0x332d;CANT_GET_FIX;LOW;Could not get fix in maximum allowed time. P1: Maximum allowed time to get a fix after the GPS was switched on.;mission/acs/archive/GPSDefinitions.h
13200;0x3390;P60_BOOT_COUNT;INFO;P60 boot count is broadcasted once at SW startup. P1: Boot count;mission/power/P60DockHandler.h
13201;0x3391;BATT_MODE;INFO;Battery mode is broadcasted at startup. P1: Mode;mission/power/P60DockHandler.h
13202;0x3392;BATT_MODE_CHANGED;MEDIUM;Battery mode has changed. P1: Old mode. P2: New mode;mission/power/P60DockHandler.h
13607;0x3527;SUPV_EVENT_BUFFER_REQUEST_TERMINATED;LOW;Terminated event buffer request by command P1: Number of packets read before process was terminated;linux/payload/PlocSupvUartMan.h
13617;0x3531;SUPV_HELPER_REQUESTING_REPLY_FAILED;LOW;Request receive message of communication interface failed P1: Return value returned by the communication interface requestReceiveMessage function P2: Internal state of supervisor helper;linux/payload/PlocSupvUartMan.h
13618;0x3532;SUPV_HELPER_READING_REPLY_FAILED;LOW;Reading receive message of communication interface failed P1: Return value returned by the communication interface readingReceivedMessage function P2: Internal state of supervisor helper;linux/payload/PlocSupvUartMan.h
13619;0x3533;SUPV_MISSING_ACK;LOW;Did not receive acknowledgement report P1: Number of bytes missing P2: Internal state of MPSoC helper;linux/payload/PlocSupvUartMan.h
13620;0x3534;SUPV_MISSING_EXE;LOW;Supervisor did not receive execution report P1: Number of bytes missing P2: Internal state of supervisor helper;linux/payload/PlocSupvUartMan.h
13621;0x3535;SUPV_ACK_FAILURE_REPORT;LOW;Supervisor received acknowledgment failure report P1: Internal state of supervisor helper;linux/payload/PlocSupvUartMan.h
13623;0x3537;SUPV_ACK_INVALID_APID;LOW;Supervisor expected acknowledgment report but received space packet with other apid P1: Apid of received space packet P2: Internal state of supervisor helper;linux/payload/PlocSupvUartMan.h
13624;0x3538;SUPV_EXE_INVALID_APID;LOW;Supervisor helper expected execution report but received space packet with other apid P1: Apid of received space packet P2: Internal state of supervisor helper;linux/payload/PlocSupvUartMan.h
13625;0x3539;ACK_RECEPTION_FAILURE;LOW;Failed to receive acknowledgment report P1: Return value P2: Apid of command for which the reception of the acknowledgment report failed;linux/payload/PlocSupvUartMan.h
13626;0x353a;EXE_RECEPTION_FAILURE;LOW;Failed to receive execution report P1: Return value P2: Apid of command for which the reception of the execution report failed;linux/payload/PlocSupvUartMan.h
13627;0x353b;WRITE_MEMORY_FAILED;LOW;Update procedure failed when sending packet. P1: First byte percent, third and fourth byte Sequence Count, P2: Bytes written;linux/payload/PlocSupvUartMan.h
13630;0x353e;SUPV_UPDATE_PROGRESS;INFO;Will be triggered every 5 percent of the update progress. P1: First byte percent, third and fourth byte Sequence Count, P2: Bytes written;linux/payload/PlocSupvUartMan.h
14001;0x36b1;REBOOT_SW;LOW; Software reboot occurred. Can also be a systemd reboot. P1: Current Chip, P2: Current Copy;bsp_q7s/core/CoreController.h
14002;0x36b2;REBOOT_MECHANISM_TRIGGERED;MEDIUM;The reboot mechanism was triggered. P1: First 16 bits: Last Chip, Last 16 bits: Last Copy, P2: Each byte is the respective reboot count for the slots;bsp_q7s/core/CoreController.h
14004;0x36b4;NO_SD_CARD_ACTIVE;HIGH;No SD card was active. Core controller will attempt to re-initialize a SD card.;bsp_q7s/core/CoreController.h
14005;0x36b5;VERSION_INFO;INFO;P1: Byte 0: Major, Byte 1: Minor, Byte 2: Patch, Byte 3: Has Git Hash P2: First four letters of Git SHA is the last byte of P1 is set.;bsp_q7s/core/CoreController.h
14006;0x36b6;CURRENT_IMAGE_INFO;INFO;P1: Current Chip, P2: Current Copy;bsp_q7s/core/CoreController.h
14007;0x36b7;REBOOT_COUNTER;INFO;Total reboot counter, which is the sum of the boot count of all individual images.;bsp_q7s/core/CoreController.h
14008;0x36b8;INDIVIDUAL_BOOT_COUNTS;INFO;Get the boot count of the individual images. P1: First 16 bits boot count of image 0 0, last 16 bits boot count of image 0 1. P2: First 16 bits boot count of image 1 0, last 16 bits boot count of image 1 1.;bsp_q7s/core/CoreController.h
14001;0x36b1;REBOOT_SW;LOW; Software reboot occurred. Can also be a systemd reboot. P1: Current Chip, P2: Current Copy;mission/sysDefs.h
14002;0x36b2;REBOOT_MECHANISM_TRIGGERED;MEDIUM;The reboot mechanism was triggered. P1: First 16 bits: Last Chip, Last 16 bits: Last Copy, P2: Each byte is the respective reboot count for the slots;mission/sysDefs.h
14004;0x36b4;NO_SD_CARD_ACTIVE;HIGH;No SD card was active. Core controller will attempt to re-initialize a SD card.;mission/sysDefs.h
14005;0x36b5;VERSION_INFO;INFO;P1: Byte 0: Major, Byte 1: Minor, Byte 2: Patch, Byte 3: Has Git Hash P2: First four letters of Git SHA is the last byte of P1 is set.;mission/sysDefs.h
14006;0x36b6;CURRENT_IMAGE_INFO;INFO;P1: Current Chip, P2: Current Copy;mission/sysDefs.h
14007;0x36b7;REBOOT_COUNTER;INFO;Total reboot counter, which is the sum of the boot count of all individual images.;mission/sysDefs.h
14008;0x36b8;INDIVIDUAL_BOOT_COUNTS;INFO;Get the boot count of the individual images. P1: First 16 bits boot count of image 0 0, last 16 bits boot count of image 0 1. P2: First 16 bits boot count of image 1 0, last 16 bits boot count of image 1 1.;mission/sysDefs.h
14010;0x36ba;TRYING_I2C_RECOVERY;HIGH;I2C is unavailable. Trying recovery of I2C bus by power cycling all I2C devices.;mission/sysDefs.h
14011;0x36bb;I2C_REBOOT;HIGH;I2C is unavailable. Recovery did not work, performing full reboot.;mission/sysDefs.h
14012;0x36bc;PDEC_REBOOT;HIGH;PDEC recovery through reset was not possible, performing full reboot.;mission/sysDefs.h
14013;0x36bd;FIRMWARE_INFO;INFO;Version information of the firmware (not OBSW). P1: Byte 0: Major, Byte 1: Minor, Byte 2: Patch, Byte 3: Has Git Hash P2: First four letters of Git SHA is the last byte of P1 is set.;mission/sysDefs.h
14014;0x36be;ACTIVE_SD_INFO;INFO;Active SD card info. SD States: 0: OFF, 1: ON, 2: MOUNTED. P1: Active SD Card Index, 0 if none is active P2: First two bytes: SD state of SD card 0, last two bytes SD state of SD card 1;mission/sysDefs.h
14111;0x371f;TCS_HEATER_MAX_BURN_TIME_REACHED;MEDIUM;P1: Heater index. P2: Maximum burn time for heater.;mission/controller/tcsDefs.h
14201;0x3779;TX_TIMER_EXPIRED;INFO;The transmit timer to protect the Syrlinks expired P1: The current timer value;mission/system/com/ComSubsystem.h
14202;0x377a;BIT_LOCK_TX_ON;INFO;Transmitter will be turned on due to detection of bitlock;mission/system/com/ComSubsystem.h
14300;0x37dc;POSSIBLE_FILE_CORRUPTION;LOW;P1: Result code of TM packet parser. P2: Timestamp of possibly corrupt file as a unix timestamp.;mission/persistentTmStoreDefs.h
14301;0x37dd;FILE_TOO_LARGE;LOW;File in store too large. P1: Detected file size P2: Allowed file size;mission/persistentTmStoreDefs.h
14501;0x38a5;TEMPERATURE_ALL_ONES_RECOVERY;INFO;Detected valid values for a prolonged time again, resetting all counters. P1: Number of periods with invalid messages. P2: Maximum invalid message counter.;mission/acs/SusHandler.h
No descriptionThe limits for the rotation in safe mode were violated.
mission/acs/defs.h
91
1120211201
0x2bc20x2bc1
MULTIPLE_RW_INVALIDRATE_RECOVERY
HIGHMEDIUM
No descriptionThe system has recovered from a rate rotation violation.
mission/acs/defs.h
92
1120311202
0x2bc30x2bc2
MEKF_INVALID_INFOMULTIPLE_RW_INVALID
INFOHIGH
No descriptionMultiple RWs are invalid, uncommandable and therefore higher ACS modes cannot be maintained.
mission/acs/defs.h
93
1120411203
0x2bc40x2bc3
MEKF_RECOVERYMEKF_INVALID_INFO
INFO
No descriptionMEKF was not able to compute a solution. P1: MEKF state on exit
mission/acs/defs.h
94
1120511204
0x2bc50x2bc4
MEKF_INVALID_MODE_VIOLATIONMEKF_RECOVERY
HIGHINFO
No descriptionMEKF is able to compute a solution again.
mission/acs/defs.h
95
1120611205
0x2bc60x2bc5
SAFE_MODE_CONTROLLER_FAILUREMEKF_AUTOMATIC_RESET
HIGHINFO
No descriptionMEKF performed an automatic reset after detection of nonfinite values.
mission/acs/defs.h
96
1130011206
0x2c240x2bc6
SWITCH_CMD_SENTPTG_CTRL_NO_ATTITUDE_INFORMATION
INFOHIGH
Indicates that a FSFW object requested setting a switch P1: 1 if on was requested, 0 for off | P2: Switch IndexFor a prolonged time, no attitude information was available for the Pointing Controller. Falling back to Safe Mode.
Indicated that a switch state has changed P1: New switch state, 1 for on, 0 for off | P2: Switch IndexThe ACS safe mode controller was not able to compute a solution and has failed. P1: Missing information about magnetic field, P2: Missing information about rotational rate
PLOC receive acknowledgment failure report P1: Command Id which leads the acknowledgment failure report P2: The status field inserted by the MPSoC into the data fieldP1: Burn duration in milliseconds, P2: Dry run flag
PLOC receive execution failure report P1: Command Id which leads the execution failure report P2: The status field inserted by the MPSoC into the data fieldP1: Burn duration in milliseconds, P2: Dry run flag
PLOC receive acknowledgment failure report P1: Command Id which leads the acknowledgment failure report P2: The status field inserted by the MPSoC into the data field
linux/payload/PlocMpsocHandler.h
129
11603
0x2d53
EXE_FAILURE
LOW
PLOC receive execution failure report P1: Command Id which leads the execution failure report P2: The status field inserted by the MPSoC into the data field
linux/payload/PlocMpsocHandler.h
130
11604
0x2d54
MPSOC_HANDLER_CRC_FAILURE
LOW
PLOC reply has invalid crc
linux/payload/PlocMpsocHandler.h
131
11605
0x2d55
MPSOC_HANDLER_SEQUENCE_COUNT_MISMATCH
LOW
Packet sequence count in received space packet does not match expected count P1: Expected sequence count P2: Received sequence count
linux/payload/PlocMpsocHandler.h
132
11606
0x2d56
MPSOC_SHUTDOWN_FAILED
HIGH
Supervisor fails to shutdown MPSoC. Requires to power off the PLOC and thus also to shutdown the supervisor.
linux/payload/PlocMpsocHandler.h
133
11607
0x2d57
SUPV_NOT_ON
LOW
SUPV not on for boot or shutdown process. P1: 0 for OFF transition, 1 for ON transition.
linux/payload/PlocMpsocHandler.h
134
11608
0x2d58
SUPV_REPLY_TIMEOUT
LOW
No description
linux/payload/PlocMpsocHandler.h
135
11701
0x2db5
SELF_TEST_I2C_FAILURE
LOW
Get self test result returns I2C failure P1: Indicates on which axis the failure occurred. 0 -> INIT, 1 -> +X, 2 -> -X, 3 -> +Y, 4 -> -Y, 5 -> +Z, 6 -> -Z, 7 -> FINA
mission/acs/ImtqHandler.h
136
11702
0x2db6
SELF_TEST_SPI_FAILURE
LOW
Get self test result returns SPI failure. This concerns the MTM connectivity. P1: Indicates on which axis the failure occurred. 0 -> INIT, 1 -> +X, 2 -> -X, 3 -> +Y, 4 -> -Y, 5 -> +Z, 6 -> -Z, 7 -> FINA
mission/acs/ImtqHandler.h
137
11703
0x2db7
SELF_TEST_ADC_FAILURE
LOW
Get self test result returns failure in measurement of current and temperature. P1: Indicates on which axis the failure occurred. 0 -> INIT, 1 -> +X, 2 -> -X, 3 -> +Y, 4 -> -Y, 5 -> +Z, 6 -> -Z, 7 -> FINA
mission/acs/ImtqHandler.h
142
11708
0x2dbc
INVALID_ERROR_BYTE
LOW
Received invalid error byte. This indicates an error of the communication link between IMTQ and OBC.
PLOC received execution failure report P1: ID of command for which the execution failed P2: Status code sent by the supervisor handlerPLOC supervisor received acknowledgment failure report
PLOC supervisor reply has invalid crcPLOC received execution failure report P1: ID of command for which the execution failed P2: Status code sent by the supervisor handler
Uploading image to star tracker was successfulopPDEC initialization failed. This might also be due to the persistent confiuration never becoming available, for example due to SD card issues.
Failed to read communication interface reply data P1: Return code of failed communication interface read call P1: Upload/download position for which the read call failedFinished flash read procedure successfully
Unexpected stop of decoding sequence P1: Return code of failed communication interface read call P1: Upload/download position for which the read call failedFlash read procedure failed
Star tracker did not send a valid reply for a certain timeout. P1: Position of upload or download packet for which the packet wa sent. P2: TimeoutFirmware update was successful
Error during decoding of received reply occurred P1: Return value of decoding function P2: Position of upload/download packet, or address of flash write/read requestFirmware update failed
Position mismatch P1: The expected position and thus the position for which the image upload/download failedFailed to read communication interface reply data P1: Return code of failed communication interface read call P1: Upload/download position for which the read call failed
Specified file does not exist P1: Internal state of str helperUnexpected stop of decoding sequence P1: Return code of failed communication interface read call P1: Upload/download position for which the read call failed
No descriptionStar tracker did not send a valid reply for a certain timeout. P1: Position of upload or download packet for which the packet wa sent. P2: Timeout
No descriptionError during decoding of received reply occurred P1: Return value of decoding function P2: Position of upload/download packet, or address of flash write/read request
Request receive message of communication interface failed P1: Return value returned by the communication interface requestReceiveMessage function P2: Internal state of MPSoC helperNo description
Reading receive message of communication interface failed P1: Return value returned by the communication interface readingReceivedMessage function P2: Internal state of MPSoC helperFlash write fails
Received acknowledgment failure report P1: Internal state of MPSoCRequest receive message of communication interface failed P1: Return value returned by the communication interface requestReceiveMessage function P2: Internal state of MPSoC helper
Received execution failure report P1: Internal state of MPSoCReading receive message of communication interface failed P1: Return value returned by the communication interface readingReceivedMessage function P2: Internal state of MPSoC helper
Expected acknowledgment report but received space packet with other apid P1: Apid of received space packet P2: Internal state of MPSoCDid not receive acknowledgment report P1: Number of bytes missing P2: Internal state of MPSoC helper
Expected execution report but received space packet with other apid P1: Apid of received space packet P2: Internal state of MPSoCDid not receive execution report P1: Number of bytes missing P2: Internal state of MPSoC helper
Received sequence count does not match expected sequence count P1: Expected sequence count P2: Received sequence countReceived acknowledgment failure report P1: Internal state of MPSoC
Could not transition properly and went back to ALL OFFExpected execution report but received space packet with other apid P1: Apid of received space packet P2: Internal state of MPSoC
P1: 0 -> too low, 1 -> too high P2: Float valueReceived sequence count does not match expected sequence count P1: Expected sequence count P2: Received sequence count
Not implemented, would increase already high complexity. Operator should instead command the assembly off first and then command the assembly on into the desired mode/submode combination
mission/system/acs/AcsBoardAssembly.h
229
12804
0x3204
DIRECT_TRANSITION_TO_DUAL_OTHER_GPS_FAULTY
MEDIUM
This is triggered when the assembly would have normally switched the board side, but the GPS device of the other side was marked faulty. P1: Current submode.
mission/system/acs/AcsBoardAssembly.h
230
12900
0x3264
TRANSITION_OTHER_SIDE_FAILED
HIGH
No description
mission/system/acs/SusAssembly.h
231
12901
0x3265
NOT_ENOUGH_DEVICES_DUAL_MODE
HIGH
No description
mission/system/acs/SusAssembly.h
232
12902
0x3266
POWER_STATE_MACHINE_TIMEOUT
MEDIUM
No description
mission/system/acs/SusAssembly.h
233
12903
0x3267
SIDE_SWITCH_TRANSITION_NOT_ALLOWED
LOW
Not implemented, would increase already high complexity. Operator should instead command the assembly off first and then command the assembly on into the desired mode/submode combination
Request receive message of communication interface failed P1: Return value returned by the communication interface requestReceiveMessage function P2: Internal state of supervisor helper
Reading receive message of communication interface failed P1: Return value returned by the communication interface readingReceivedMessage function P2: Internal state of supervisor helper
Supervisor expected acknowledgment report but received space packet with other apid P1: Apid of received space packet P2: Internal state of supervisor helper
Supervisor helper expected execution report but received space packet with other apid P1: Apid of received space packet P2: Internal state of supervisor helper
Software reboot occurred. Can also be a systemd reboot. P1: Current Chip, P2: Current Copy
bsp_q7s/core/CoreController.hmission/sysDefs.h
280
14002
0x36b2
REBOOT_MECHANISM_TRIGGERED
MEDIUM
The reboot mechanism was triggered. P1: First 16 bits: Last Chip, Last 16 bits: Last Copy, P2: Each byte is the respective reboot count for the slots
bsp_q7s/core/CoreController.hmission/sysDefs.h
281
14003
0x36b3
REBOOT_HW
MEDIUM
No description
bsp_q7s/core/CoreController.hmission/sysDefs.h
282
14004
0x36b4
NO_SD_CARD_ACTIVE
HIGH
No SD card was active. Core controller will attempt to re-initialize a SD card.
bsp_q7s/core/CoreController.hmission/sysDefs.h
283
14005
0x36b5
VERSION_INFO
INFO
P1: Byte 0: Major, Byte 1: Minor, Byte 2: Patch, Byte 3: Has Git Hash P2: First four letters of Git SHA is the last byte of P1 is set.
bsp_q7s/core/CoreController.hmission/sysDefs.h
284
14006
0x36b6
CURRENT_IMAGE_INFO
INFO
P1: Current Chip, P2: Current Copy
bsp_q7s/core/CoreController.hmission/sysDefs.h
285
14007
0x36b7
REBOOT_COUNTER
INFO
Total reboot counter, which is the sum of the boot count of all individual images.
bsp_q7s/core/CoreController.hmission/sysDefs.h
286
14008
0x36b8
INDIVIDUAL_BOOT_COUNTS
INFO
Get the boot count of the individual images. P1: First 16 bits boot count of image 0 0, last 16 bits boot count of image 0 1. P2: First 16 bits boot count of image 1 0, last 16 bits boot count of image 1 1.
bsp_q7s/core/CoreController.hmission/sysDefs.h
287
14010
0x36ba
I2C_UNAVAILABLE_REBOOTTRYING_I2C_RECOVERY
MEDIUMHIGH
No descriptionI2C is unavailable. Trying recovery of I2C bus by power cycling all I2C devices.
bsp_q7s/core/CoreController.hmission/sysDefs.h
288
1410014011
0x37140x36bb
NO_VALID_SENSOR_TEMPERATUREI2C_REBOOT
MEDIUMHIGH
No descriptionI2C is unavailable. Recovery did not work, performing full reboot.
No descriptionVersion information of the firmware (not OBSW). P1: Byte 0: Major, Byte 1: Minor, Byte 2: Patch, Byte 3: Has Git Hash P2: First four letters of Git SHA is the last byte of P1 is set.
No descriptionActive SD card info. SD States: 0: OFF, 1: ON, 2: MOUNTED. P1: Active SD Card Index, 0 if none is active P2: First two bytes: SD state of SD card 0, last two bytes SD state of SD card 1
Detected valid values for a prolonged time again, resetting all counters. P1: Number of periods with invalid messages. P2: Maximum invalid message counter.
0x4400;UXOS_ExecutionFinished;Execution of the current command has finished;0;LINUX_OSAL;fsfw/src/fsfw_hal/linux/CommandExecutor.h
0x4401;UXOS_CommandPending;Command is pending. This will also be returned if the user tries to load another command but a command is still pending;1;LINUX_OSAL;fsfw/src/fsfw_hal/linux/CommandExecutor.h
0x4402;UXOS_BytesRead;Some bytes have been read from the executing process;2;LINUX_OSAL;fsfw/src/fsfw_hal/linux/CommandExecutor.h
0x51a7;IMTQ_UnexpectedSelfTestReply;The status reply to a self test command was received but no self test command has been sent. This should normally never happen.;167;IMTQ_HANDLER;mission/acs/imtqHelpers.h
0x52b1;RWHA_SpiReadFailure;Used by the spi send function to tell a failing read call;177;RW_HANDLER;mission/acs/rwHelpers.h
0x52b2;RWHA_MissingStartSign;Can be used by the HDLC decoding mechanism to inform about a missing start sign 0x7E;178;RW_HANDLER;mission/acs/rwHelpers.h
0x52b3;RWHA_InvalidSubstitute;Can be used by the HDLC decoding mechanism to inform about an invalid substitution combination;179;RW_HANDLER;mission/acs/rwHelpers.h
0x52b4;RWHA_MissingEndSign;HDLC decoding mechanism never receives the end sign 0x7E;180;RW_HANDLER;mission/acs/rwHelpers.h
0x52b5;RWHA_NoReply;Reaction wheel only responds with empty frames.;181;RW_HANDLER;mission/acs/rwHelpers.h
0x52b6;RWHA_NoStartMarker;Expected a start marker as first byte;182;RW_HANDLER;mission/acs/rwHelpers.h
0x52b7;RWHA_SpiReadTimeout;Timeout when reading reply;183;RW_HANDLER;mission/acs/rwHelpers.h
0x58a0;SUSS_InvalidSpeed;Action Message with invalid speed was received. Valid speeds must be in the range of [-65000, 1000] or [1000, 65000];160;SUS_HANDLER;mission/acs/RwHandler.h
0x58a1;SUSS_InvalidRampTime;Action Message with invalid ramp time was received.;161;SUS_HANDLER;mission/acs/RwHandler.h
0x58a2;SUSS_SetSpeedCommandInvalidLength;Received set speed command has invalid length. Should be 6.;162;SUS_HANDLER;mission/acs/RwHandler.h
0x4500;UXOS_ExecutionFinished;Execution of the current command has finished;0;LINUX_OSAL;fsfw/src/fsfw_hal/linux/CommandExecutor.h
0x4501;UXOS_CommandPending;Command is pending. This will also be returned if the user tries to load another command but a command is still pending;1;LINUX_OSAL;fsfw/src/fsfw_hal/linux/CommandExecutor.h
0x4502;UXOS_BytesRead;Some bytes have been read from the executing process;2;LINUX_OSAL;fsfw/src/fsfw_hal/linux/CommandExecutor.h
0x520a;IMTQ_UnexpectedSelfTestReply;The status reply to a self test command was received but no self test command has been sent. This should normally never happen.;10;IMTQ_HANDLER;mission/acs/imtqHelpers.h
0x53a0;RWHA_InvalidSpeed;Action Message with invalid speed was received. Valid speeds must be in the range of [-65000, 1000] or [1000, 65000];160;RW_HANDLER;mission/acs/RwHandler.h
0x53a1;RWHA_InvalidRampTime;Action Message with invalid ramp time was received.;161;RW_HANDLER;mission/acs/RwHandler.h
0x53a2;RWHA_SetSpeedCommandInvalidLength;Received set speed command has invalid length. Should be 6.;162;RW_HANDLER;mission/acs/RwHandler.h
0x53b1;RWHA_SpiReadFailure;Used by the spi send function to tell a failing read call;177;RW_HANDLER;mission/acs/rwHelpers.h
0x53b2;RWHA_MissingStartSign;Can be used by the HDLC decoding mechanism to inform about a missing start sign 0x7E;178;RW_HANDLER;mission/acs/rwHelpers.h
0x53b3;RWHA_InvalidSubstitute;Can be used by the HDLC decoding mechanism to inform about an invalid substitution combination;179;RW_HANDLER;mission/acs/rwHelpers.h
0x53b4;RWHA_MissingEndSign;HDLC decoding mechanism never receives the end sign 0x7E;180;RW_HANDLER;mission/acs/rwHelpers.h
0x53b5;RWHA_NoReply;Reaction wheel only responds with empty frames.;181;RW_HANDLER;mission/acs/rwHelpers.h
0x53b6;RWHA_NoStartMarker;Expected a start marker as first byte;182;RW_HANDLER;mission/acs/rwHelpers.h
0x53b7;RWHA_SpiReadTimeout;Timeout when reading reply;183;RW_HANDLER;mission/acs/rwHelpers.h
0x54a0;STRH_TemperatureReqFailed;Status in temperature reply signals error;160;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54a8;STRH_FilenameTooLong;Name of file received with command is too long;168;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54a9;STRH_InvalidProgram;Received version reply with invalid program ID;169;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54aa;STRH_ReplyError;Status field reply signals error;170;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54ab;STRH_CommandTooShort;Received command which is too short (some data is missing for proper execution);171;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54ac;STRH_InvalidLength;Received command with invalid length (too few or too many parameters);172;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54ad;STRH_RegionMismatch;Region mismatch between send and received data;173;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54ae;STRH_AddressMismatch;Address mismatch between send and received data;174;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54af;STRH_LengthMismatch;Length field mismatch between send and received data;175;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54b0;STRH_FileNotExists;Specified file does not exist;176;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54b1;STRH_InvalidType;Download blob pixel command has invalid type field;177;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54b2;STRH_InvalidId;Received FPGA action command with invalid ID;178;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54b3;STRH_ReplyTooShort;Received reply is too short;179;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54b4;STRH_CrcFailure;Received reply with invalid CRC;180;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54b5;STRH_StrHelperExecuting;Star tracker handler currently executing a command and using the communication interface;181;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54b6;STRH_StartrackerAlreadyBooted;Star tracker is already in firmware mode;182;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54b7;STRH_StartrackerNotRunningFirmware;Star tracker must be in firmware mode to run this command;183;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54b8;STRH_StartrackerNotRunningBootloader;Star tracker must be in bootloader mode to run this command;184;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x6aa0;ACSCTRL_FileDeletionFailed;File deletion failed and at least one file is still existent.;160;ACS_CTRL;mission/controller/controllerdefinitions/AcsCtrlDefinitions.h
0x6aa1;ACSCTRL_WriteFileFailed;Writing the TLE to the file has failed.;161;ACS_CTRL;mission/controller/controllerdefinitions/AcsCtrlDefinitions.h
0x6aa2;ACSCTRL_ReadFileFailed;Reading the TLE to the file has failed.;162;ACS_CTRL;mission/controller/controllerdefinitions/AcsCtrlDefinitions.h
0x6aa3;ACSCTRL_SingleRwUnavailable;A single RW has failed.;163;ACS_CTRL;mission/controller/controllerdefinitions/AcsCtrlDefinitions.h
0x6aa4;ACSCTRL_MultipleRwUnavailable;Multiple RWs have failed.;164;ACS_CTRL;mission/controller/controllerdefinitions/AcsCtrlDefinitions.h
Received set speed command has invalid length. Should be 6.No description
1629
SUS_HANDLERIMTQ_HANDLER
mission/acs/RwHandler.hmission/acs/imtqHelpers.h
456
0x58a30x520a
SUSS_ExecutionFailedIMTQ_UnexpectedSelfTestReply
Command execution failedThe status reply to a self test command was received but no self test command has been sent. This should normally never happen.
16310
SUS_HANDLERIMTQ_HANDLER
mission/acs/RwHandler.hmission/acs/imtqHelpers.h
457
0x58a40x53a0
SUSS_CrcErrorRWHA_InvalidSpeed
Reaction wheel reply has invalid crcAction Message with invalid speed was received. Valid speeds must be in the range of [-65000, 1000] or [1000, 65000]
164160
SUS_HANDLERRW_HANDLER
mission/acs/RwHandler.h
458
0x58a50x53a1
SUSS_ValueNotReadRWHA_InvalidRampTime
No descriptionAction Message with invalid ramp time was received.
11300;0x2c24;SWITCH_CMD_SENT;INFO;Indicates that a FSFW object requested setting a switch P1: 1 if on was requested, 0 for off | P2: Switch Index;mission/devices/devicedefinitions/powerDefinitions.h
11301;0x2c25;SWITCH_HAS_CHANGED;INFO;Indicated that a switch state has changed P1: New switch state, 1 for on, 0 for off | P2: Switch Index;mission/devices/devicedefinitions/powerDefinitions.h
11601;0x2d51;MEMORY_READ_RPT_CRC_FAILURE;LOW;PLOC crc failure in telemetry packet;linux/devices/ploc/PlocMPSoCHandler.h
11602;0x2d52;ACK_FAILURE;LOW;PLOC receive acknowledgment failure report P1: Command Id which leads the acknowledgment failure report P2: The status field inserted by the MPSoC into the data field;linux/devices/ploc/PlocMPSoCHandler.h
11603;0x2d53;EXE_FAILURE;LOW;PLOC receive execution failure report P1: Command Id which leads the execution failure report P2: The status field inserted by the MPSoC into the data field;linux/devices/ploc/PlocMPSoCHandler.h
11604;0x2d54;MPSOC_HANDLER_CRC_FAILURE;LOW;PLOC reply has invalid crc;linux/devices/ploc/PlocMPSoCHandler.h
11605;0x2d55;MPSOC_HANDLER_SEQUENCE_COUNT_MISMATCH;LOW;Packet sequence count in received space packet does not match expected count P1: Expected sequence count P2: Received sequence count;linux/devices/ploc/PlocMPSoCHandler.h
11606;0x2d56;MPSOC_SHUTDOWN_FAILED;HIGH;Supervisor fails to shutdown MPSoC. Requires to power off the PLOC and thus also to shutdown the supervisor.;linux/devices/ploc/PlocMPSoCHandler.h
11200;0x2bc0;SAFE_RATE_VIOLATION;MEDIUM;The limits for the rotation in safe mode were violated.;mission/acs/defs.h
11201;0x2bc1;RATE_RECOVERY;MEDIUM;The system has recovered from a rate rotation violation.;mission/acs/defs.h
11202;0x2bc2;MULTIPLE_RW_INVALID;HIGH;Multiple RWs are invalid, uncommandable and therefore higher ACS modes cannot be maintained.;mission/acs/defs.h
11203;0x2bc3;MEKF_INVALID_INFO;INFO;MEKF was not able to compute a solution. P1: MEKF state on exit;mission/acs/defs.h
11204;0x2bc4;MEKF_RECOVERY;INFO;MEKF is able to compute a solution again.;mission/acs/defs.h
11205;0x2bc5;MEKF_AUTOMATIC_RESET;INFO;MEKF performed an automatic reset after detection of nonfinite values.;mission/acs/defs.h
11206;0x2bc6;PTG_CTRL_NO_ATTITUDE_INFORMATION;HIGH;For a prolonged time, no attitude information was available for the Pointing Controller. Falling back to Safe Mode.;mission/acs/defs.h
11207;0x2bc7;SAFE_MODE_CONTROLLER_FAILURE;HIGH;The ACS safe mode controller was not able to compute a solution and has failed. P1: Missing information about magnetic field, P2: Missing information about rotational rate;mission/acs/defs.h
11208;0x2bc8;TLE_TOO_OLD;INFO;The TLE for the SGP4 Propagator has become too old.;mission/acs/defs.h
11209;0x2bc9;TLE_FILE_READ_FAILED;LOW;The TLE could not be read from the filesystem.;mission/acs/defs.h
11210;0x2bca;PTG_RATE_VIOLATION;MEDIUM;The limits for the rotation in pointing mode were violated.;mission/acs/defs.h
11300;0x2c24;SWITCH_CMD_SENT;INFO;Indicates that a FSFW object requested setting a switch P1: 1 if on was requested, 0 for off | P2: Switch Index;mission/power/defs.h
11301;0x2c25;SWITCH_HAS_CHANGED;INFO;Indicated that a switch state has changed P1: New switch state, 1 for on, 0 for off | P2: Switch Index;mission/power/defs.h
11306;0x2c2a;TIMEDELTA_OUT_OF_BOUNDS;LOW;Time difference for Coulomb Counter was too large. P1: time in s * 10;mission/power/defs.h
11307;0x2c2b;POWER_LEVEL_LOW;HIGH;The State of Charge is below the limit for payload use. Setting Payload to faulty.;mission/power/defs.h
11308;0x2c2c;POWER_LEVEL_CRITICAL;HIGH;The State of Charge is below the limit for higher modes. Setting Reaction Wheels to faulty.;mission/power/defs.h
11601;0x2d51;MEMORY_READ_RPT_CRC_FAILURE;LOW;PLOC crc failure in telemetry packet;linux/payload/PlocMpsocHandler.h
11602;0x2d52;ACK_FAILURE;LOW;PLOC receive acknowledgment failure report P1: Command Id which leads the acknowledgment failure report P2: The status field inserted by the MPSoC into the data field;linux/payload/PlocMpsocHandler.h
11603;0x2d53;EXE_FAILURE;LOW;PLOC receive execution failure report P1: Command Id which leads the execution failure report P2: The status field inserted by the MPSoC into the data field;linux/payload/PlocMpsocHandler.h
11604;0x2d54;MPSOC_HANDLER_CRC_FAILURE;LOW;PLOC reply has invalid crc;linux/payload/PlocMpsocHandler.h
11605;0x2d55;MPSOC_HANDLER_SEQUENCE_COUNT_MISMATCH;LOW;Packet sequence count in received space packet does not match expected count P1: Expected sequence count P2: Received sequence count;linux/payload/PlocMpsocHandler.h
11606;0x2d56;MPSOC_SHUTDOWN_FAILED;HIGH;Supervisor fails to shutdown MPSoC. Requires to power off the PLOC and thus also to shutdown the supervisor.;linux/payload/PlocMpsocHandler.h
11607;0x2d57;SUPV_NOT_ON;LOW;SUPV not on for boot or shutdown process. P1: 0 for OFF transition, 1 for ON transition.;linux/payload/PlocMpsocHandler.h
11701;0x2db5;SELF_TEST_I2C_FAILURE;LOW;Get self test result returns I2C failure P1: Indicates on which axis the failure occurred. 0 -> INIT, 1 -> +X, 2 -> -X, 3 -> +Y, 4 -> -Y, 5 -> +Z, 6 -> -Z, 7 -> FINA;mission/acs/ImtqHandler.h
11702;0x2db6;SELF_TEST_SPI_FAILURE;LOW;Get self test result returns SPI failure. This concerns the MTM connectivity. P1: Indicates on which axis the failure occurred. 0 -> INIT, 1 -> +X, 2 -> -X, 3 -> +Y, 4 -> -Y, 5 -> +Z, 6 -> -Z, 7 -> FINA;mission/acs/ImtqHandler.h
11703;0x2db7;SELF_TEST_ADC_FAILURE;LOW;Get self test result returns failure in measurement of current and temperature. P1: Indicates on which axis the failure occurred. 0 -> INIT, 1 -> +X, 2 -> -X, 3 -> +Y, 4 -> -Y, 5 -> +Z, 6 -> -Z, 7 -> FINA;mission/acs/ImtqHandler.h
@ -130,151 +142,179 @@ Event ID (dec); Event ID (hex); Name; Severity; Description; File Path
11708;0x2dbc;INVALID_ERROR_BYTE;LOW;Received invalid error byte. This indicates an error of the communication link between IMTQ and OBC.;mission/acs/ImtqHandler.h
11801;0x2e19;ERROR_STATE;HIGH;Reaction wheel signals an error state;mission/acs/rwHelpers.h
12004;0x2ee4;SUPV_ACK_FAILURE;LOW;PLOC supervisor received acknowledgment failure report;linux/devices/ploc/PlocSupervisorHandler.h
12005;0x2ee5;SUPV_EXE_FAILURE;LOW;PLOC received execution failure report P1: ID of command for which the execution failed P2: Status code sent by the supervisor handler;linux/devices/ploc/PlocSupervisorHandler.h
12006;0x2ee6;SUPV_CRC_FAILURE_EVENT;LOW;PLOC supervisor reply has invalid crc;linux/devices/ploc/PlocSupervisorHandler.h
12007;0x2ee7;SUPV_HELPER_EXECUTING;LOW;Supervisor helper currently executing a command;linux/devices/ploc/PlocSupervisorHandler.h
12008;0x2ee8;SUPV_MPSOC_SHUTDOWN_BUILD_FAILED;LOW;Failed to build the command to shutdown the MPSoC;linux/devices/ploc/PlocSupervisorHandler.h
11901;0x2e7d;BOOTING_FIRMWARE_FAILED_EVENT;LOW;Failed to boot firmware;mission/acs/str/StarTrackerHandler.h
11902;0x2e7e;BOOTING_BOOTLOADER_FAILED_EVENT;LOW;Failed to boot star tracker into bootloader mode;mission/acs/str/StarTrackerHandler.h
11903;0x2e7f;COM_ERROR_REPLY_RECEIVED;LOW;Received COM error. P1: Communication Error ID (datasheet p32);mission/acs/str/StarTrackerHandler.h
12001;0x2ee1;SUPV_MEMORY_READ_RPT_CRC_FAILURE;LOW;PLOC supervisor crc failure in telemetry packet;linux/payload/plocSupvDefs.h
12002;0x2ee2;SUPV_UNKNOWN_TM;LOW;Unhandled event. P1: APID, P2: Service ID;linux/payload/plocSupvDefs.h
12004;0x2ee4;SUPV_ACK_FAILURE;LOW;PLOC supervisor received acknowledgment failure report;linux/payload/plocSupvDefs.h
12005;0x2ee5;SUPV_EXE_FAILURE;LOW;PLOC received execution failure report P1: ID of command for which the execution failed P2: Status code sent by the supervisor handler;linux/payload/plocSupvDefs.h
12006;0x2ee6;SUPV_CRC_FAILURE_EVENT;LOW;PLOC supervisor reply has invalid crc;linux/payload/plocSupvDefs.h
12007;0x2ee7;SUPV_HELPER_EXECUTING;LOW;Supervisor helper currently executing a command;linux/payload/plocSupvDefs.h
12008;0x2ee8;SUPV_MPSOC_SHUTDOWN_BUILD_FAILED;LOW;Failed to build the command to shutdown the MPSoC;linux/payload/plocSupvDefs.h
12009;0x2ee9;SUPV_ACK_UNKNOWN_COMMAND;LOW;Received ACK, but no related command is unknown or has not been sent by this software instance. P1: Module APID. P2: Service ID.;linux/payload/plocSupvDefs.h
12010;0x2eea;SUPV_EXE_ACK_UNKNOWN_COMMAND;LOW;Received ACK EXE, but no related command is unknown or has not been sent by this software instance. P1: Module APID. P2: Service ID.;linux/payload/plocSupvDefs.h
12300;0x300c;SEND_MRAM_DUMP_FAILED;LOW;Failed to send mram dump command to supervisor handler P1: Return value of commandAction function P2: Start address of MRAM to dump with this command;linux/devices/ploc/PlocMemoryDumper.h
12301;0x300d;MRAM_DUMP_FAILED;LOW;Received completion failure report form PLOC supervisor handler P1: MRAM start address of failing dump command;linux/devices/ploc/PlocMemoryDumper.h
12509;0x30dd;STR_HELPER_READING_REPLY_FAILED;LOW;Failed to read communication interface reply data P1: Return code of failed communication interface read call P1: Upload/download position for which the read call failed;linux/acs/startracker/StrComHandler.h
12510;0x30de;STR_HELPER_COM_ERROR;LOW;Unexpected stop of decoding sequence P1: Return code of failed communication interface read call P1: Upload/download position for which the read call failed;linux/acs/startracker/StrComHandler.h
12511;0x30df;STR_COM_REPLY_TIMEOUT;LOW;Star tracker did not send a valid reply for a certain timeout. P1: Position of upload or download packet for which the packet wa sent. P2: Timeout;linux/acs/startracker/StrComHandler.h
12513;0x30e1;STR_HELPER_DEC_ERROR;LOW;Error during decoding of received reply occurred P1: Return value of decoding function P2: Position of upload/download packet, or address of flash write/read request;linux/acs/startracker/StrComHandler.h
12514;0x30e2;POSITION_MISMATCH;LOW;Position mismatch P1: The expected position and thus the position for which the image upload/download failed;linux/acs/startracker/StrComHandler.h
12515;0x30e3;STR_HELPER_FILE_NOT_EXISTS;LOW;Specified file does not exist P1: Internal state of str helper;linux/acs/startracker/StrComHandler.h
12603;0x313b;MPSOC_HELPER_REQUESTING_REPLY_FAILED;LOW;Request receive message of communication interface failed P1: Return value returned by the communication interface requestReceiveMessage function P2: Internal state of MPSoC helper;linux/devices/ploc/PlocMPSoCHelper.h
12604;0x313c;MPSOC_HELPER_READING_REPLY_FAILED;LOW;Reading receive message of communication interface failed P1: Return value returned by the communication interface readingReceivedMessage function P2: Internal state of MPSoC helper;linux/devices/ploc/PlocMPSoCHelper.h
12605;0x313d;MPSOC_MISSING_ACK;LOW;Did not receive acknowledgment report P1: Number of bytes missing P2: Internal state of MPSoC helper;linux/devices/ploc/PlocMPSoCHelper.h
12606;0x313e;MPSOC_MISSING_EXE;LOW;Did not receive execution report P1: Number of bytes missing P2: Internal state of MPSoC helper;linux/devices/ploc/PlocMPSoCHelper.h
12607;0x313f;MPSOC_ACK_FAILURE_REPORT;LOW;Received acknowledgment failure report P1: Internal state of MPSoC;linux/devices/ploc/PlocMPSoCHelper.h
12608;0x3140;MPSOC_EXE_FAILURE_REPORT;LOW;Received execution failure report P1: Internal state of MPSoC;linux/devices/ploc/PlocMPSoCHelper.h
12609;0x3141;MPSOC_ACK_INVALID_APID;LOW;Expected acknowledgment report but received space packet with other apid P1: Apid of received space packet P2: Internal state of MPSoC;linux/devices/ploc/PlocMPSoCHelper.h
12610;0x3142;MPSOC_EXE_INVALID_APID;LOW;Expected execution report but received space packet with other apid P1: Apid of received space packet P2: Internal state of MPSoC;linux/devices/ploc/PlocMPSoCHelper.h
12611;0x3143;MPSOC_HELPER_SEQ_CNT_MISMATCH;LOW;Received sequence count does not match expected sequence count P1: Expected sequence count P2: Received sequence count;linux/devices/ploc/PlocMPSoCHelper.h
12700;0x319c;TRANSITION_BACK_TO_OFF;MEDIUM;Could not transition properly and went back to ALL OFF;mission/devices/PayloadPcduHandler.h
12701;0x319d;NEG_V_OUT_OF_BOUNDS;MEDIUM;P1: 0 -> too low, 1 -> too high P2: Float value;mission/devices/PayloadPcduHandler.h
12702;0x319e;U_DRO_OUT_OF_BOUNDS;MEDIUM;P1: 0 -> too low, 1 -> too high P2: Float value;mission/devices/PayloadPcduHandler.h
12703;0x319f;I_DRO_OUT_OF_BOUNDS;MEDIUM;P1: 0 -> too low, 1 -> too high P2: Float value;mission/devices/PayloadPcduHandler.h
12704;0x31a0;U_X8_OUT_OF_BOUNDS;MEDIUM;P1: 0 -> too low, 1 -> too high P2: Float value;mission/devices/PayloadPcduHandler.h
12705;0x31a1;I_X8_OUT_OF_BOUNDS;MEDIUM;P1: 0 -> too low, 1 -> too high P2: Float value;mission/devices/PayloadPcduHandler.h
12706;0x31a2;U_TX_OUT_OF_BOUNDS;MEDIUM;P1: 0 -> too low, 1 -> too high P2: Float value;mission/devices/PayloadPcduHandler.h
12707;0x31a3;I_TX_OUT_OF_BOUNDS;MEDIUM;P1: 0 -> too low, 1 -> too high P2: Float value;mission/devices/PayloadPcduHandler.h
12708;0x31a4;U_MPA_OUT_OF_BOUNDS;MEDIUM;P1: 0 -> too low, 1 -> too high P2: Float value;mission/devices/PayloadPcduHandler.h
12709;0x31a5;I_MPA_OUT_OF_BOUNDS;MEDIUM;P1: 0 -> too low, 1 -> too high P2: Float value;mission/devices/PayloadPcduHandler.h
12710;0x31a6;U_HPA_OUT_OF_BOUNDS;MEDIUM;P1: 0 -> too low, 1 -> too high P2: Float value;mission/devices/PayloadPcduHandler.h
12711;0x31a7;I_HPA_OUT_OF_BOUNDS;MEDIUM;P1: 0 -> too low, 1 -> too high P2: Float value;mission/devices/PayloadPcduHandler.h
12300;0x300c;SEND_MRAM_DUMP_FAILED;LOW;Failed to send mram dump command to supervisor handler P1: Return value of commandAction function P2: Start address of MRAM to dump with this command;linux/payload/PlocMemoryDumper.h
12301;0x300d;MRAM_DUMP_FAILED;LOW;Received completion failure report form PLOC supervisor handler P1: MRAM start address of failing dump command;linux/payload/PlocMemoryDumper.h
12410;0x307a;PDEC_TRYING_RESET_WITH_INIT;LOW;Trying a PDEC reset with complete re-initialization;linux/ipcore/pdec.h
12411;0x307b;PDEC_TRYING_RESET_NO_INIT;LOW;Trying a PDEC reset without re-initialization.;linux/ipcore/pdec.h
12412;0x307c;PDEC_RESET_FAILED;HIGH;Failed to pull PDEC reset to low;linux/ipcore/pdec.h
12413;0x307d;OPEN_IRQ_FILE_FAILED;HIGH;Failed to open the IRQ uio file;linux/ipcore/pdec.h
12414;0x307e;PDEC_INIT_FAILED;HIGH;PDEC initialization failed. This might also be due to the persistent confiuration never becoming available, for example due to SD card issues.;linux/ipcore/pdec.h
12415;0x307f;PDEC_CONFIG_CORRUPTED;HIGH;The PDEC configuration area has been corrupted P1: The first configuration word P2: The second configuration word;linux/ipcore/pdec.h
12509;0x30dd;STR_HELPER_READING_REPLY_FAILED;LOW;Failed to read communication interface reply data P1: Return code of failed communication interface read call P1: Upload/download position for which the read call failed;linux/acs/StrComHandler.h
12510;0x30de;STR_HELPER_COM_ERROR;LOW;Unexpected stop of decoding sequence P1: Return code of failed communication interface read call P1: Upload/download position for which the read call failed;linux/acs/StrComHandler.h
12511;0x30df;STR_COM_REPLY_TIMEOUT;LOW;Star tracker did not send a valid reply for a certain timeout. P1: Position of upload or download packet for which the packet wa sent. P2: Timeout;linux/acs/StrComHandler.h
12513;0x30e1;STR_HELPER_DEC_ERROR;LOW;Error during decoding of received reply occurred P1: Return value of decoding function P2: Position of upload/download packet, or address of flash write/read request;linux/acs/StrComHandler.h
12514;0x30e2;POSITION_MISMATCH;LOW;Position mismatch P1: The expected position and thus the position for which the image upload/download failed;linux/acs/StrComHandler.h
12515;0x30e3;STR_HELPER_FILE_NOT_EXISTS;LOW;Specified file does not exist P1: Internal state of str helper;linux/acs/StrComHandler.h
12603;0x313b;MPSOC_HELPER_REQUESTING_REPLY_FAILED;LOW;Request receive message of communication interface failed P1: Return value returned by the communication interface requestReceiveMessage function P2: Internal state of MPSoC helper;linux/payload/PlocMpsocSpecialComHelper.h
12604;0x313c;MPSOC_HELPER_READING_REPLY_FAILED;LOW;Reading receive message of communication interface failed P1: Return value returned by the communication interface readingReceivedMessage function P2: Internal state of MPSoC helper;linux/payload/PlocMpsocSpecialComHelper.h
12605;0x313d;MPSOC_MISSING_ACK;LOW;Did not receive acknowledgment report P1: Number of bytes missing P2: Internal state of MPSoC helper;linux/payload/PlocMpsocSpecialComHelper.h
12606;0x313e;MPSOC_MISSING_EXE;LOW;Did not receive execution report P1: Number of bytes missing P2: Internal state of MPSoC helper;linux/payload/PlocMpsocSpecialComHelper.h
12607;0x313f;MPSOC_ACK_FAILURE_REPORT;LOW;Received acknowledgment failure report P1: Internal state of MPSoC;linux/payload/PlocMpsocSpecialComHelper.h
12608;0x3140;MPSOC_EXE_FAILURE_REPORT;LOW;Received execution failure report P1: Internal state of MPSoC;linux/payload/PlocMpsocSpecialComHelper.h
12609;0x3141;MPSOC_ACK_INVALID_APID;LOW;Expected acknowledgment report but received space packet with other apid P1: Apid of received space packet P2: Internal state of MPSoC;linux/payload/PlocMpsocSpecialComHelper.h
12610;0x3142;MPSOC_EXE_INVALID_APID;LOW;Expected execution report but received space packet with other apid P1: Apid of received space packet P2: Internal state of MPSoC;linux/payload/PlocMpsocSpecialComHelper.h
12611;0x3143;MPSOC_HELPER_SEQ_CNT_MISMATCH;LOW;Received sequence count does not match expected sequence count P1: Expected sequence count P2: Received sequence count;linux/payload/PlocMpsocSpecialComHelper.h
12803;0x3203;SIDE_SWITCH_TRANSITION_NOT_ALLOWED;LOW;Not implemented, would increase already high complexity. Operator should instead command the assembly off first and then command the assembly on into the desired mode/submode combination;mission/system/acs/AcsBoardAssembly.h
12804;0x3204;DIRECT_TRANSITION_TO_DUAL_OTHER_GPS_FAULTY;MEDIUM;This is triggered when the assembly would have normally switched the board side, but the GPS device of the other side was marked faulty. P1: Current submode.;mission/system/acs/AcsBoardAssembly.h
12903;0x3267;SIDE_SWITCH_TRANSITION_NOT_ALLOWED;LOW;Not implemented, would increase already high complexity. Operator should instead command the assembly off first and then command the assembly on into the desired mode/submode combination;mission/system/acs/SusAssembly.h
13100;0x332c;GPS_FIX_CHANGE;INFO;Fix has changed. P1: Old fix. P2: New fix 0: Not seen, 1: No Fix, 2: 2D-Fix, 3: 3D-Fix;mission/devices/devicedefinitions/GPSDefinitions.h
13101;0x332d;CANT_GET_FIX;LOW;Could not get fix in maximum allowed time. P1: Maximum allowed time to get a fix after the GPS was switched on.;mission/devices/devicedefinitions/GPSDefinitions.h
13200;0x3390;P60_BOOT_COUNT;INFO;P60 boot count is broadcasted once at SW startup. P1: Boot count;mission/devices/P60DockHandler.h
13201;0x3391;BATT_MODE;INFO;Battery mode is broadcasted at startup. P1: Mode;mission/devices/P60DockHandler.h
13202;0x3392;BATT_MODE_CHANGED;MEDIUM;Battery mode has changed. P1: Old mode. P2: New mode;mission/devices/P60DockHandler.h
13607;0x3527;SUPV_EVENT_BUFFER_REQUEST_TERMINATED;LOW;Terminated event buffer request by command P1: Number of packets read before process was terminated;linux/devices/ploc/PlocSupvUartMan.h
13617;0x3531;SUPV_HELPER_REQUESTING_REPLY_FAILED;LOW;Request receive message of communication interface failed P1: Return value returned by the communication interface requestReceiveMessage function P2: Internal state of supervisor helper;linux/devices/ploc/PlocSupvUartMan.h
13618;0x3532;SUPV_HELPER_READING_REPLY_FAILED;LOW;Reading receive message of communication interface failed P1: Return value returned by the communication interface readingReceivedMessage function P2: Internal state of supervisor helper;linux/devices/ploc/PlocSupvUartMan.h
13619;0x3533;SUPV_MISSING_ACK;LOW;Did not receive acknowledgement report P1: Number of bytes missing P2: Internal state of MPSoC helper;linux/devices/ploc/PlocSupvUartMan.h
13620;0x3534;SUPV_MISSING_EXE;LOW;Supervisor did not receive execution report P1: Number of bytes missing P2: Internal state of supervisor helper;linux/devices/ploc/PlocSupvUartMan.h
13621;0x3535;SUPV_ACK_FAILURE_REPORT;LOW;Supervisor received acknowledgment failure report P1: Internal state of supervisor helper;linux/devices/ploc/PlocSupvUartMan.h
13623;0x3537;SUPV_ACK_INVALID_APID;LOW;Supervisor expected acknowledgment report but received space packet with other apid P1: Apid of received space packet P2: Internal state of supervisor helper;linux/devices/ploc/PlocSupvUartMan.h
13624;0x3538;SUPV_EXE_INVALID_APID;LOW;Supervisor helper expected execution report but received space packet with other apid P1: Apid of received space packet P2: Internal state of supervisor helper;linux/devices/ploc/PlocSupvUartMan.h
13625;0x3539;ACK_RECEPTION_FAILURE;LOW;Failed to receive acknowledgment report P1: Return value P2: Apid of command for which the reception of the acknowledgment report failed;linux/devices/ploc/PlocSupvUartMan.h
13626;0x353a;EXE_RECEPTION_FAILURE;LOW;Failed to receive execution report P1: Return value P2: Apid of command for which the reception of the execution report failed;linux/devices/ploc/PlocSupvUartMan.h
13627;0x353b;WRITE_MEMORY_FAILED;LOW;Update procedure failed when sending packet. P1: First byte percent, third and fourth byte Sequence Count, P2: Bytes written;linux/devices/ploc/PlocSupvUartMan.h
13630;0x353e;SUPV_UPDATE_PROGRESS;INFO;Will be triggered every 5 percent of the update progress. P1: First byte percent, third and fourth byte Sequence Count, P2: Bytes written;linux/devices/ploc/PlocSupvUartMan.h
13100;0x332c;GPS_FIX_CHANGE;INFO;Fix has changed. P1: Old fix. P2: New fix 0: Not seen, 1: No Fix, 2: 2D-Fix, 3: 3D-Fix;mission/acs/archive/GPSDefinitions.h
13101;0x332d;CANT_GET_FIX;LOW;Could not get fix in maximum allowed time. P1: Maximum allowed time to get a fix after the GPS was switched on.;mission/acs/archive/GPSDefinitions.h
13200;0x3390;P60_BOOT_COUNT;INFO;P60 boot count is broadcasted once at SW startup. P1: Boot count;mission/power/P60DockHandler.h
13201;0x3391;BATT_MODE;INFO;Battery mode is broadcasted at startup. P1: Mode;mission/power/P60DockHandler.h
13202;0x3392;BATT_MODE_CHANGED;MEDIUM;Battery mode has changed. P1: Old mode. P2: New mode;mission/power/P60DockHandler.h
13607;0x3527;SUPV_EVENT_BUFFER_REQUEST_TERMINATED;LOW;Terminated event buffer request by command P1: Number of packets read before process was terminated;linux/payload/PlocSupvUartMan.h
13617;0x3531;SUPV_HELPER_REQUESTING_REPLY_FAILED;LOW;Request receive message of communication interface failed P1: Return value returned by the communication interface requestReceiveMessage function P2: Internal state of supervisor helper;linux/payload/PlocSupvUartMan.h
13618;0x3532;SUPV_HELPER_READING_REPLY_FAILED;LOW;Reading receive message of communication interface failed P1: Return value returned by the communication interface readingReceivedMessage function P2: Internal state of supervisor helper;linux/payload/PlocSupvUartMan.h
13619;0x3533;SUPV_MISSING_ACK;LOW;Did not receive acknowledgement report P1: Number of bytes missing P2: Internal state of MPSoC helper;linux/payload/PlocSupvUartMan.h
13620;0x3534;SUPV_MISSING_EXE;LOW;Supervisor did not receive execution report P1: Number of bytes missing P2: Internal state of supervisor helper;linux/payload/PlocSupvUartMan.h
13621;0x3535;SUPV_ACK_FAILURE_REPORT;LOW;Supervisor received acknowledgment failure report P1: Internal state of supervisor helper;linux/payload/PlocSupvUartMan.h
13623;0x3537;SUPV_ACK_INVALID_APID;LOW;Supervisor expected acknowledgment report but received space packet with other apid P1: Apid of received space packet P2: Internal state of supervisor helper;linux/payload/PlocSupvUartMan.h
13624;0x3538;SUPV_EXE_INVALID_APID;LOW;Supervisor helper expected execution report but received space packet with other apid P1: Apid of received space packet P2: Internal state of supervisor helper;linux/payload/PlocSupvUartMan.h
13625;0x3539;ACK_RECEPTION_FAILURE;LOW;Failed to receive acknowledgment report P1: Return value P2: Apid of command for which the reception of the acknowledgment report failed;linux/payload/PlocSupvUartMan.h
13626;0x353a;EXE_RECEPTION_FAILURE;LOW;Failed to receive execution report P1: Return value P2: Apid of command for which the reception of the execution report failed;linux/payload/PlocSupvUartMan.h
13627;0x353b;WRITE_MEMORY_FAILED;LOW;Update procedure failed when sending packet. P1: First byte percent, third and fourth byte Sequence Count, P2: Bytes written;linux/payload/PlocSupvUartMan.h
13630;0x353e;SUPV_UPDATE_PROGRESS;INFO;Will be triggered every 5 percent of the update progress. P1: First byte percent, third and fourth byte Sequence Count, P2: Bytes written;linux/payload/PlocSupvUartMan.h
14001;0x36b1;REBOOT_SW;LOW; Software reboot occurred. Can also be a systemd reboot. P1: Current Chip, P2: Current Copy;bsp_q7s/core/CoreController.h
14002;0x36b2;REBOOT_MECHANISM_TRIGGERED;MEDIUM;The reboot mechanism was triggered. P1: First 16 bits: Last Chip, Last 16 bits: Last Copy, P2: Each byte is the respective reboot count for the slots;bsp_q7s/core/CoreController.h
14004;0x36b4;NO_SD_CARD_ACTIVE;HIGH;No SD card was active. Core controller will attempt to re-initialize a SD card.;bsp_q7s/core/CoreController.h
14005;0x36b5;VERSION_INFO;INFO;P1: Byte 0: Major, Byte 1: Minor, Byte 2: Patch, Byte 3: Has Git Hash P2: First four letters of Git SHA is the last byte of P1 is set.;bsp_q7s/core/CoreController.h
14006;0x36b6;CURRENT_IMAGE_INFO;INFO;P1: Current Chip, P2: Current Copy;bsp_q7s/core/CoreController.h
14007;0x36b7;REBOOT_COUNTER;INFO;Total reboot counter, which is the sum of the boot count of all individual images.;bsp_q7s/core/CoreController.h
14008;0x36b8;INDIVIDUAL_BOOT_COUNTS;INFO;Get the boot count of the individual images. P1: First 16 bits boot count of image 0 0, last 16 bits boot count of image 0 1. P2: First 16 bits boot count of image 1 0, last 16 bits boot count of image 1 1.;bsp_q7s/core/CoreController.h
14001;0x36b1;REBOOT_SW;LOW; Software reboot occurred. Can also be a systemd reboot. P1: Current Chip, P2: Current Copy;mission/sysDefs.h
14002;0x36b2;REBOOT_MECHANISM_TRIGGERED;MEDIUM;The reboot mechanism was triggered. P1: First 16 bits: Last Chip, Last 16 bits: Last Copy, P2: Each byte is the respective reboot count for the slots;mission/sysDefs.h
14004;0x36b4;NO_SD_CARD_ACTIVE;HIGH;No SD card was active. Core controller will attempt to re-initialize a SD card.;mission/sysDefs.h
14005;0x36b5;VERSION_INFO;INFO;P1: Byte 0: Major, Byte 1: Minor, Byte 2: Patch, Byte 3: Has Git Hash P2: First four letters of Git SHA is the last byte of P1 is set.;mission/sysDefs.h
14006;0x36b6;CURRENT_IMAGE_INFO;INFO;P1: Current Chip, P2: Current Copy;mission/sysDefs.h
14007;0x36b7;REBOOT_COUNTER;INFO;Total reboot counter, which is the sum of the boot count of all individual images.;mission/sysDefs.h
14008;0x36b8;INDIVIDUAL_BOOT_COUNTS;INFO;Get the boot count of the individual images. P1: First 16 bits boot count of image 0 0, last 16 bits boot count of image 0 1. P2: First 16 bits boot count of image 1 0, last 16 bits boot count of image 1 1.;mission/sysDefs.h
14010;0x36ba;TRYING_I2C_RECOVERY;HIGH;I2C is unavailable. Trying recovery of I2C bus by power cycling all I2C devices.;mission/sysDefs.h
14011;0x36bb;I2C_REBOOT;HIGH;I2C is unavailable. Recovery did not work, performing full reboot.;mission/sysDefs.h
14012;0x36bc;PDEC_REBOOT;HIGH;PDEC recovery through reset was not possible, performing full reboot.;mission/sysDefs.h
14013;0x36bd;FIRMWARE_INFO;INFO;Version information of the firmware (not OBSW). P1: Byte 0: Major, Byte 1: Minor, Byte 2: Patch, Byte 3: Has Git Hash P2: First four letters of Git SHA is the last byte of P1 is set.;mission/sysDefs.h
14014;0x36be;ACTIVE_SD_INFO;INFO;Active SD card info. SD States: 0: OFF, 1: ON, 2: MOUNTED. P1: Active SD Card Index, 0 if none is active P2: First two bytes: SD state of SD card 0, last two bytes SD state of SD card 1;mission/sysDefs.h
14111;0x371f;TCS_HEATER_MAX_BURN_TIME_REACHED;MEDIUM;P1: Heater index. P2: Maximum burn time for heater.;mission/controller/tcsDefs.h
14201;0x3779;TX_TIMER_EXPIRED;INFO;The transmit timer to protect the Syrlinks expired P1: The current timer value;mission/system/com/ComSubsystem.h
14202;0x377a;BIT_LOCK_TX_ON;INFO;Transmitter will be turned on due to detection of bitlock;mission/system/com/ComSubsystem.h
14300;0x37dc;POSSIBLE_FILE_CORRUPTION;LOW;P1: Result code of TM packet parser. P2: Timestamp of possibly corrupt file as a unix timestamp.;mission/persistentTmStoreDefs.h
14301;0x37dd;FILE_TOO_LARGE;LOW;File in store too large. P1: Detected file size P2: Allowed file size;mission/persistentTmStoreDefs.h
14501;0x38a5;TEMPERATURE_ALL_ONES_RECOVERY;INFO;Detected valid values for a prolonged time again, resetting all counters. P1: Number of periods with invalid messages. P2: Maximum invalid message counter.;mission/acs/SusHandler.h
No descriptionThe limits for the rotation in safe mode were violated.
mission/acs/defs.h
91
1120211201
0x2bc20x2bc1
MULTIPLE_RW_INVALIDRATE_RECOVERY
HIGHMEDIUM
No descriptionThe system has recovered from a rate rotation violation.
mission/acs/defs.h
92
1120311202
0x2bc30x2bc2
MEKF_INVALID_INFOMULTIPLE_RW_INVALID
INFOHIGH
No descriptionMultiple RWs are invalid, uncommandable and therefore higher ACS modes cannot be maintained.
mission/acs/defs.h
93
1120411203
0x2bc40x2bc3
MEKF_RECOVERYMEKF_INVALID_INFO
INFO
No descriptionMEKF was not able to compute a solution. P1: MEKF state on exit
mission/acs/defs.h
94
1120511204
0x2bc50x2bc4
MEKF_INVALID_MODE_VIOLATIONMEKF_RECOVERY
HIGHINFO
No descriptionMEKF is able to compute a solution again.
mission/acs/defs.h
95
1120611205
0x2bc60x2bc5
SAFE_MODE_CONTROLLER_FAILUREMEKF_AUTOMATIC_RESET
HIGHINFO
No descriptionMEKF performed an automatic reset after detection of nonfinite values.
mission/acs/defs.h
96
1130011206
0x2c240x2bc6
SWITCH_CMD_SENTPTG_CTRL_NO_ATTITUDE_INFORMATION
INFOHIGH
Indicates that a FSFW object requested setting a switch P1: 1 if on was requested, 0 for off | P2: Switch IndexFor a prolonged time, no attitude information was available for the Pointing Controller. Falling back to Safe Mode.
Indicated that a switch state has changed P1: New switch state, 1 for on, 0 for off | P2: Switch IndexThe ACS safe mode controller was not able to compute a solution and has failed. P1: Missing information about magnetic field, P2: Missing information about rotational rate
PLOC receive acknowledgment failure report P1: Command Id which leads the acknowledgment failure report P2: The status field inserted by the MPSoC into the data fieldP1: Burn duration in milliseconds, P2: Dry run flag
PLOC receive execution failure report P1: Command Id which leads the execution failure report P2: The status field inserted by the MPSoC into the data fieldP1: Burn duration in milliseconds, P2: Dry run flag
PLOC receive acknowledgment failure report P1: Command Id which leads the acknowledgment failure report P2: The status field inserted by the MPSoC into the data field
linux/payload/PlocMpsocHandler.h
129
11603
0x2d53
EXE_FAILURE
LOW
PLOC receive execution failure report P1: Command Id which leads the execution failure report P2: The status field inserted by the MPSoC into the data field
linux/payload/PlocMpsocHandler.h
130
11604
0x2d54
MPSOC_HANDLER_CRC_FAILURE
LOW
PLOC reply has invalid crc
linux/payload/PlocMpsocHandler.h
131
11605
0x2d55
MPSOC_HANDLER_SEQUENCE_COUNT_MISMATCH
LOW
Packet sequence count in received space packet does not match expected count P1: Expected sequence count P2: Received sequence count
linux/payload/PlocMpsocHandler.h
132
11606
0x2d56
MPSOC_SHUTDOWN_FAILED
HIGH
Supervisor fails to shutdown MPSoC. Requires to power off the PLOC and thus also to shutdown the supervisor.
linux/payload/PlocMpsocHandler.h
133
11607
0x2d57
SUPV_NOT_ON
LOW
SUPV not on for boot or shutdown process. P1: 0 for OFF transition, 1 for ON transition.
linux/payload/PlocMpsocHandler.h
134
11608
0x2d58
SUPV_REPLY_TIMEOUT
LOW
No description
linux/payload/PlocMpsocHandler.h
135
11701
0x2db5
SELF_TEST_I2C_FAILURE
LOW
Get self test result returns I2C failure P1: Indicates on which axis the failure occurred. 0 -> INIT, 1 -> +X, 2 -> -X, 3 -> +Y, 4 -> -Y, 5 -> +Z, 6 -> -Z, 7 -> FINA
mission/acs/ImtqHandler.h
136
11702
0x2db6
SELF_TEST_SPI_FAILURE
LOW
Get self test result returns SPI failure. This concerns the MTM connectivity. P1: Indicates on which axis the failure occurred. 0 -> INIT, 1 -> +X, 2 -> -X, 3 -> +Y, 4 -> -Y, 5 -> +Z, 6 -> -Z, 7 -> FINA
mission/acs/ImtqHandler.h
137
11703
0x2db7
SELF_TEST_ADC_FAILURE
LOW
Get self test result returns failure in measurement of current and temperature. P1: Indicates on which axis the failure occurred. 0 -> INIT, 1 -> +X, 2 -> -X, 3 -> +Y, 4 -> -Y, 5 -> +Z, 6 -> -Z, 7 -> FINA
mission/acs/ImtqHandler.h
142
11708
0x2dbc
INVALID_ERROR_BYTE
LOW
Received invalid error byte. This indicates an error of the communication link between IMTQ and OBC.
PLOC received execution failure report P1: ID of command for which the execution failed P2: Status code sent by the supervisor handlerPLOC supervisor received acknowledgment failure report
PLOC supervisor reply has invalid crcPLOC received execution failure report P1: ID of command for which the execution failed P2: Status code sent by the supervisor handler
Uploading image to star tracker was successfulopPDEC initialization failed. This might also be due to the persistent confiuration never becoming available, for example due to SD card issues.
Failed to read communication interface reply data P1: Return code of failed communication interface read call P1: Upload/download position for which the read call failedFinished flash read procedure successfully
Unexpected stop of decoding sequence P1: Return code of failed communication interface read call P1: Upload/download position for which the read call failedFlash read procedure failed
Star tracker did not send a valid reply for a certain timeout. P1: Position of upload or download packet for which the packet wa sent. P2: TimeoutFirmware update was successful
Error during decoding of received reply occurred P1: Return value of decoding function P2: Position of upload/download packet, or address of flash write/read requestFirmware update failed
Position mismatch P1: The expected position and thus the position for which the image upload/download failedFailed to read communication interface reply data P1: Return code of failed communication interface read call P1: Upload/download position for which the read call failed
Specified file does not exist P1: Internal state of str helperUnexpected stop of decoding sequence P1: Return code of failed communication interface read call P1: Upload/download position for which the read call failed
No descriptionStar tracker did not send a valid reply for a certain timeout. P1: Position of upload or download packet for which the packet wa sent. P2: Timeout
No descriptionError during decoding of received reply occurred P1: Return value of decoding function P2: Position of upload/download packet, or address of flash write/read request
Request receive message of communication interface failed P1: Return value returned by the communication interface requestReceiveMessage function P2: Internal state of MPSoC helperNo description
Reading receive message of communication interface failed P1: Return value returned by the communication interface readingReceivedMessage function P2: Internal state of MPSoC helperFlash write fails
Received acknowledgment failure report P1: Internal state of MPSoCRequest receive message of communication interface failed P1: Return value returned by the communication interface requestReceiveMessage function P2: Internal state of MPSoC helper
Received execution failure report P1: Internal state of MPSoCReading receive message of communication interface failed P1: Return value returned by the communication interface readingReceivedMessage function P2: Internal state of MPSoC helper
Expected acknowledgment report but received space packet with other apid P1: Apid of received space packet P2: Internal state of MPSoCDid not receive acknowledgment report P1: Number of bytes missing P2: Internal state of MPSoC helper
Expected execution report but received space packet with other apid P1: Apid of received space packet P2: Internal state of MPSoCDid not receive execution report P1: Number of bytes missing P2: Internal state of MPSoC helper
Received sequence count does not match expected sequence count P1: Expected sequence count P2: Received sequence countReceived acknowledgment failure report P1: Internal state of MPSoC
Could not transition properly and went back to ALL OFFExpected execution report but received space packet with other apid P1: Apid of received space packet P2: Internal state of MPSoC
P1: 0 -> too low, 1 -> too high P2: Float valueReceived sequence count does not match expected sequence count P1: Expected sequence count P2: Received sequence count
Not implemented, would increase already high complexity. Operator should instead command the assembly off first and then command the assembly on into the desired mode/submode combination
mission/system/acs/AcsBoardAssembly.h
229
12804
0x3204
DIRECT_TRANSITION_TO_DUAL_OTHER_GPS_FAULTY
MEDIUM
This is triggered when the assembly would have normally switched the board side, but the GPS device of the other side was marked faulty. P1: Current submode.
mission/system/acs/AcsBoardAssembly.h
230
12900
0x3264
TRANSITION_OTHER_SIDE_FAILED
HIGH
No description
mission/system/acs/SusAssembly.h
231
12901
0x3265
NOT_ENOUGH_DEVICES_DUAL_MODE
HIGH
No description
mission/system/acs/SusAssembly.h
232
12902
0x3266
POWER_STATE_MACHINE_TIMEOUT
MEDIUM
No description
mission/system/acs/SusAssembly.h
233
12903
0x3267
SIDE_SWITCH_TRANSITION_NOT_ALLOWED
LOW
Not implemented, would increase already high complexity. Operator should instead command the assembly off first and then command the assembly on into the desired mode/submode combination
Request receive message of communication interface failed P1: Return value returned by the communication interface requestReceiveMessage function P2: Internal state of supervisor helper
Reading receive message of communication interface failed P1: Return value returned by the communication interface readingReceivedMessage function P2: Internal state of supervisor helper
Supervisor expected acknowledgment report but received space packet with other apid P1: Apid of received space packet P2: Internal state of supervisor helper
Supervisor helper expected execution report but received space packet with other apid P1: Apid of received space packet P2: Internal state of supervisor helper
Software reboot occurred. Can also be a systemd reboot. P1: Current Chip, P2: Current Copy
bsp_q7s/core/CoreController.hmission/sysDefs.h
280
14002
0x36b2
REBOOT_MECHANISM_TRIGGERED
MEDIUM
The reboot mechanism was triggered. P1: First 16 bits: Last Chip, Last 16 bits: Last Copy, P2: Each byte is the respective reboot count for the slots
bsp_q7s/core/CoreController.hmission/sysDefs.h
281
14003
0x36b3
REBOOT_HW
MEDIUM
No description
bsp_q7s/core/CoreController.hmission/sysDefs.h
282
14004
0x36b4
NO_SD_CARD_ACTIVE
HIGH
No SD card was active. Core controller will attempt to re-initialize a SD card.
bsp_q7s/core/CoreController.hmission/sysDefs.h
283
14005
0x36b5
VERSION_INFO
INFO
P1: Byte 0: Major, Byte 1: Minor, Byte 2: Patch, Byte 3: Has Git Hash P2: First four letters of Git SHA is the last byte of P1 is set.
bsp_q7s/core/CoreController.hmission/sysDefs.h
284
14006
0x36b6
CURRENT_IMAGE_INFO
INFO
P1: Current Chip, P2: Current Copy
bsp_q7s/core/CoreController.hmission/sysDefs.h
285
14007
0x36b7
REBOOT_COUNTER
INFO
Total reboot counter, which is the sum of the boot count of all individual images.
bsp_q7s/core/CoreController.hmission/sysDefs.h
286
14008
0x36b8
INDIVIDUAL_BOOT_COUNTS
INFO
Get the boot count of the individual images. P1: First 16 bits boot count of image 0 0, last 16 bits boot count of image 0 1. P2: First 16 bits boot count of image 1 0, last 16 bits boot count of image 1 1.
bsp_q7s/core/CoreController.hmission/sysDefs.h
287
14010
0x36ba
I2C_UNAVAILABLE_REBOOTTRYING_I2C_RECOVERY
MEDIUMHIGH
No descriptionI2C is unavailable. Trying recovery of I2C bus by power cycling all I2C devices.
bsp_q7s/core/CoreController.hmission/sysDefs.h
288
1410014011
0x37140x36bb
NO_VALID_SENSOR_TEMPERATUREI2C_REBOOT
MEDIUMHIGH
No descriptionI2C is unavailable. Recovery did not work, performing full reboot.
No descriptionVersion information of the firmware (not OBSW). P1: Byte 0: Major, Byte 1: Minor, Byte 2: Patch, Byte 3: Has Git Hash P2: First four letters of Git SHA is the last byte of P1 is set.
No descriptionActive SD card info. SD States: 0: OFF, 1: ON, 2: MOUNTED. P1: Active SD Card Index, 0 if none is active P2: First two bytes: SD state of SD card 0, last two bytes SD state of SD card 1
Detected valid values for a prolonged time again, resetting all counters. P1: Number of periods with invalid messages. P2: Maximum invalid message counter.
0x4400;UXOS_ExecutionFinished;Execution of the current command has finished;0;LINUX_OSAL;fsfw/src/fsfw_hal/linux/CommandExecutor.h
0x4401;UXOS_CommandPending;Command is pending. This will also be returned if the user tries to load another command but a command is still pending;1;LINUX_OSAL;fsfw/src/fsfw_hal/linux/CommandExecutor.h
0x4402;UXOS_BytesRead;Some bytes have been read from the executing process;2;LINUX_OSAL;fsfw/src/fsfw_hal/linux/CommandExecutor.h
0x51a7;IMTQ_UnexpectedSelfTestReply;The status reply to a self test command was received but no self test command has been sent. This should normally never happen.;167;IMTQ_HANDLER;mission/acs/imtqHelpers.h
0x52b1;RWHA_SpiReadFailure;Used by the spi send function to tell a failing read call;177;RW_HANDLER;mission/acs/rwHelpers.h
0x52b2;RWHA_MissingStartSign;Can be used by the HDLC decoding mechanism to inform about a missing start sign 0x7E;178;RW_HANDLER;mission/acs/rwHelpers.h
0x52b3;RWHA_InvalidSubstitute;Can be used by the HDLC decoding mechanism to inform about an invalid substitution combination;179;RW_HANDLER;mission/acs/rwHelpers.h
0x52b4;RWHA_MissingEndSign;HDLC decoding mechanism never receives the end sign 0x7E;180;RW_HANDLER;mission/acs/rwHelpers.h
0x52b5;RWHA_NoReply;Reaction wheel only responds with empty frames.;181;RW_HANDLER;mission/acs/rwHelpers.h
0x52b6;RWHA_NoStartMarker;Expected a start marker as first byte;182;RW_HANDLER;mission/acs/rwHelpers.h
0x52b7;RWHA_SpiReadTimeout;Timeout when reading reply;183;RW_HANDLER;mission/acs/rwHelpers.h
0x53a0;STRH_TemperatureReqFailed;Status in temperature reply signals error;160;STR_HANDLER;linux/acs/startracker/StarTrackerHandler.h
0x53a8;STRH_FilenameTooLong;Name of file received with command is too long;168;STR_HANDLER;linux/acs/startracker/StarTrackerHandler.h
0x53a9;STRH_InvalidProgram;Received version reply with invalid program ID;169;STR_HANDLER;linux/acs/startracker/StarTrackerHandler.h
0x53aa;STRH_ReplyError;Status field reply signals error;170;STR_HANDLER;linux/acs/startracker/StarTrackerHandler.h
0x53ab;STRH_CommandTooShort;Received command which is tooshort (some data is missing for proper execution);171;STR_HANDLER;linux/acs/startracker/StarTrackerHandler.h
0x53ac;STRH_InvalidLength;Received command with invalid length (too few or too many parameters);172;STR_HANDLER;linux/acs/startracker/StarTrackerHandler.h
0x53ad;STRH_RegionMismatch;Region mismatch between send and received data;173;STR_HANDLER;linux/acs/startracker/StarTrackerHandler.h
0x53ae;STRH_AddressMismatch;Address mismatch between send and received data;174;STR_HANDLER;linux/acs/startracker/StarTrackerHandler.h
0x53af;STRH_LengthMismatch;Length field mismatch between send and received data;175;STR_HANDLER;linux/acs/startracker/StarTrackerHandler.h
0x53b0;STRH_FileNotExists;Specified file does not exist;176;STR_HANDLER;linux/acs/startracker/StarTrackerHandler.h
0x53b1;STRH_InvalidType;Download blob pixel command has invalid type field;177;STR_HANDLER;linux/acs/startracker/StarTrackerHandler.h
0x53b2;STRH_InvalidId;Received FPGA action command with invalid ID;178;STR_HANDLER;linux/acs/startracker/StarTrackerHandler.h
0x53b3;STRH_ReplyTooShort;Received reply is too short;179;STR_HANDLER;linux/acs/startracker/StarTrackerHandler.h
0x53b4;STRH_CrcFailure;Received reply with invalid CRC;180;STR_HANDLER;linux/acs/startracker/StarTrackerHandler.h
0x53b5;STRH_StrHelperExecuting;Star tracker handler currently executing a command and using the communication interface;181;STR_HANDLER;linux/acs/startracker/StarTrackerHandler.h
0x53b6;STRH_StartrackerAlreadyBooted;Star tracker is already in firmware mode;182;STR_HANDLER;linux/acs/startracker/StarTrackerHandler.h
0x53b7;STRH_StartrackerNotRunningFirmware;Star tracker must be in firmware mode to run this command;183;STR_HANDLER;linux/acs/startracker/StarTrackerHandler.h
0x53b8;STRH_StartrackerNotRunningBootloader;Star tracker must be in bootloader mode to run this command;184;STR_HANDLER;linux/acs/startracker/StarTrackerHandler.h
0x54e0;DWLPWRON_InvalidMode;Received command has invalid JESD mode (valid modes are 0 - 5);224;DWLPWRON_CMD;linux/devices/devicedefinitions/PlocMPSoCDefinitions.h
0x54e1;DWLPWRON_InvalidLaneRate;Received command has invalid lane rate (valid lane rate are 0 - 9);225;DWLPWRON_CMD;linux/devices/devicedefinitions/PlocMPSoCDefinitions.h
0x57a1;PLSPVhLP_ProcessTerminated;Process has been terminated by command;161;PLOC_SUPV_HELPER;linux/devices/ploc/PlocSupvUartMan.h
0x57a2;PLSPVhLP_PathNotExists;Received command with invalid pathname;162;PLOC_SUPV_HELPER;linux/devices/ploc/PlocSupvUartMan.h
0x57a3;PLSPVhLP_EventBufferReplyInvalidApid;Expected event buffer TM but received space packet with other APID;163;PLOC_SUPV_HELPER;linux/devices/ploc/PlocSupvUartMan.h
0x58a0;SUSS_InvalidSpeed;Action Message with invalid speed was received. Valid speeds must be in the range of [-65000, 1000] or [1000, 65000];160;SUS_HANDLER;mission/acs/RwHandler.h
0x58a1;SUSS_InvalidRampTime;Action Message with invalid ramp time was received.;161;SUS_HANDLER;mission/acs/RwHandler.h
0x58a2;SUSS_SetSpeedCommandInvalidLength;Received set speed command has invalid length. Should be 6.;162;SUS_HANDLER;mission/acs/RwHandler.h
0x5ea0;PLMEMDUMP_MramAddressTooHigh;The capacity of the MRAM amounts to 512 kB. Thus the maximum address must not be higher than 0x7d000.;160;PLOC_MEMORY_DUMPER;linux/devices/ploc/PlocMemoryDumper.h
0x5ea1;PLMEMDUMP_MramInvalidAddressCombination;The specified end address is lower than the start address;161;PLOC_MEMORY_DUMPER;linux/devices/ploc/PlocMemoryDumper.h
0x5fb0;PDEC_CommandNotImplemented;Received action message with unknown action id;176;PDEC_HANDLER;linux/ipcore/PdecHandler.h
0x60a0;CCSDS_CommandNotImplemented;Received action message with unknown action id;160;CCSDS_HANDLER;mission/com/CcsdsIpCoreHandler.h
0x61a0;RS_RateNotSupported;The commanded rate is not supported by the current FPGA design;160;RATE_SETTER;linux/ipcore/PtmeConfig.h
0x61a1;RS_BadBitRate;Bad bitrate has been commanded (e.g. 0);161;RATE_SETTER;linux/ipcore/PtmeConfig.h
0x61a2;RS_ClkInversionFailed;Failed to invert clock and thus change the time the data is updated with respect to the tx clock;162;RATE_SETTER;linux/ipcore/PtmeConfig.h
0x61a3;RS_TxManipulatorConfigFailed;Failed to change configuration bit of tx clock manipulator;163;RATE_SETTER;linux/ipcore/PtmeConfig.h
0x6201;JSONBASE_JsonFileNotExists;Specified json file does not exist;1;ARCSEC_JSON_BASE;linux/acs/startracker/ArcsecJsonParamBase.h
0x6202;JSONBASE_SetNotExists;Requested set does not exist in json file;2;ARCSEC_JSON_BASE;linux/acs/startracker/ArcsecJsonParamBase.h
0x6203;JSONBASE_ParamNotExists;Requested parameter does not exist in json file;3;ARCSEC_JSON_BASE;linux/acs/startracker/ArcsecJsonParamBase.h
0x63a0;NVMB_KeyNotExists;Specified key does not exist in json file;160;NVM_PARAM_BASE;mission/memory/NvmParameterBase.h
0x64a0;FSHLP_SdNotMounted;SD card specified with path string not mounted;160;FILE_SYSTEM_HELPER;bsp_q7s/fs/FilesystemHelper.h
0x64a1;FSHLP_FileNotExists;Specified file does not exist on filesystem;161;FILE_SYSTEM_HELPER;bsp_q7s/fs/FilesystemHelper.h
0x67a0;MPSOCRTVIF_CrcFailure;Space Packet received from PLOC has invalid CRC;160;MPSOC_RETURN_VALUES_IF;linux/devices/devicedefinitions/MPSoCReturnValuesIF.h
0x67a1;MPSOCRTVIF_ReceivedAckFailure;Received ACK failure reply from PLOC;161;MPSOC_RETURN_VALUES_IF;linux/devices/devicedefinitions/MPSoCReturnValuesIF.h
0x67a2;MPSOCRTVIF_ReceivedExeFailure;Received execution failure reply from PLOC;162;MPSOC_RETURN_VALUES_IF;linux/devices/devicedefinitions/MPSoCReturnValuesIF.h
0x67a3;MPSOCRTVIF_InvalidApid;Received space packet with invalid APID from PLOC;163;MPSOC_RETURN_VALUES_IF;linux/devices/devicedefinitions/MPSoCReturnValuesIF.h
0x67a4;MPSOCRTVIF_InvalidLength;Received command with invalid length;164;MPSOC_RETURN_VALUES_IF;linux/devices/devicedefinitions/MPSoCReturnValuesIF.h
0x67a5;MPSOCRTVIF_FilenameTooLong;Filename of file in OBC filesystem is too long;165;MPSOC_RETURN_VALUES_IF;linux/devices/devicedefinitions/MPSoCReturnValuesIF.h
0x67a6;MPSOCRTVIF_MpsocHelperExecuting;MPSoC helper is currently executing a command;166;MPSOC_RETURN_VALUES_IF;linux/devices/devicedefinitions/MPSoCReturnValuesIF.h
0x67a7;MPSOCRTVIF_MpsocFilenameTooLong;Filename of MPSoC file is to long (max. 256 bytes);167;MPSOC_RETURN_VALUES_IF;linux/devices/devicedefinitions/MPSoCReturnValuesIF.h
0x67a8;MPSOCRTVIF_InvalidParameter;Command has invalid parameter;168;MPSOC_RETURN_VALUES_IF;linux/devices/devicedefinitions/MPSoCReturnValuesIF.h
0x67a9;MPSOCRTVIF_NameTooLong;Received command has file string with invalid length;169;MPSOC_RETURN_VALUES_IF;linux/devices/devicedefinitions/MPSoCReturnValuesIF.h
0x68a0;SPVRTVIF_CrcFailure;Space Packet received from PLOC supervisor has invalid CRC;160;SUPV_RETURN_VALUES_IF;linux/devices/devicedefinitions/PlocSupervisorDefinitions.h
0x68a2;SPVRTVIF_ReceivedAckFailure;Received ACK failure reply from PLOC supervisor;162;SUPV_RETURN_VALUES_IF;linux/devices/devicedefinitions/PlocSupervisorDefinitions.h
0x68a3;SPVRTVIF_ReceivedExeFailure;Received execution failure reply from PLOC supervisor;163;SUPV_RETURN_VALUES_IF;linux/devices/devicedefinitions/PlocSupervisorDefinitions.h
0x68a4;SPVRTVIF_InvalidApid;Received space packet with invalid APID from PLOC supervisor;164;SUPV_RETURN_VALUES_IF;linux/devices/devicedefinitions/PlocSupervisorDefinitions.h
0x68a5;SPVRTVIF_GetTimeFailure;Failed to read current system time;165;SUPV_RETURN_VALUES_IF;linux/devices/devicedefinitions/PlocSupervisorDefinitions.h
0x68a6;SPVRTVIF_InvalidWatchdog;Received command with invalid watchdog parameter. Valid watchdogs are 0 for PS, 1 for PL and 2 for INT;166;SUPV_RETURN_VALUES_IF;linux/devices/devicedefinitions/PlocSupervisorDefinitions.h
0x68a7;SPVRTVIF_InvalidWatchdogTimeout;Received watchdog timeout config command with invalid timeout. Valid timeouts must be in the range between 1000 and 360000 ms.;167;SUPV_RETURN_VALUES_IF;linux/devices/devicedefinitions/PlocSupervisorDefinitions.h
0x68a8;SPVRTVIF_InvalidLatchupId;Received latchup config command with invalid latchup ID;168;SUPV_RETURN_VALUES_IF;linux/devices/devicedefinitions/PlocSupervisorDefinitions.h
0x68a9;SPVRTVIF_SweepPeriodTooSmall;Received set adc sweep period command with invalid sweep period. Must be larger than 21.;169;SUPV_RETURN_VALUES_IF;linux/devices/devicedefinitions/PlocSupervisorDefinitions.h
0x68aa;SPVRTVIF_InvalidTestParam;Receive auto EM test command with invalid test param. Valid params are 1 and 2.;170;SUPV_RETURN_VALUES_IF;linux/devices/devicedefinitions/PlocSupervisorDefinitions.h
0x68ab;SPVRTVIF_MramPacketParsingFailure;Returned when scanning for MRAM dump packets failed.;171;SUPV_RETURN_VALUES_IF;linux/devices/devicedefinitions/PlocSupervisorDefinitions.h
0x68ac;SPVRTVIF_InvalidMramAddresses;Returned when the start and stop addresses of the MRAM dump or MRAM wipe commands are invalid (e.g. start address bigger than stop address);172;SUPV_RETURN_VALUES_IF;linux/devices/devicedefinitions/PlocSupervisorDefinitions.h
0x68ad;SPVRTVIF_NoMramPacket;Expect reception of an MRAM dump packet but received space packet with other apid.;173;SUPV_RETURN_VALUES_IF;linux/devices/devicedefinitions/PlocSupervisorDefinitions.h
0x68ae;SPVRTVIF_PathDoesNotExist;Path to PLOC directory on SD card does not exist;174;SUPV_RETURN_VALUES_IF;linux/devices/devicedefinitions/PlocSupervisorDefinitions.h
0x68af;SPVRTVIF_MramFileNotExists;MRAM dump file does not exists. The file should actually already have been created with the reception of the first dump packet.;175;SUPV_RETURN_VALUES_IF;linux/devices/devicedefinitions/PlocSupervisorDefinitions.h
0x68b1;SPVRTVIF_InvalidLength;Received action command has invalid length;177;SUPV_RETURN_VALUES_IF;linux/devices/devicedefinitions/PlocSupervisorDefinitions.h
0x68b2;SPVRTVIF_FilenameTooLong;Filename too long;178;SUPV_RETURN_VALUES_IF;linux/devices/devicedefinitions/PlocSupervisorDefinitions.h
0x68b3;SPVRTVIF_UpdateStatusReportInvalidLength;Received update status report with invalid packet length field;179;SUPV_RETURN_VALUES_IF;linux/devices/devicedefinitions/PlocSupervisorDefinitions.h
0x68b4;SPVRTVIF_UpdateCrcFailure;Update status report does not contain expected CRC. There might be a bit flip in the update memory region.;180;SUPV_RETURN_VALUES_IF;linux/devices/devicedefinitions/PlocSupervisorDefinitions.h
0x68b5;SPVRTVIF_SupvHelperExecuting;Supervisor helper task ist currently executing a command (wait until helper tas has finished or interrupt by sending the terminate command);181;SUPV_RETURN_VALUES_IF;linux/devices/devicedefinitions/PlocSupervisorDefinitions.h
0x4500;UXOS_ExecutionFinished;Execution of the current command has finished;0;LINUX_OSAL;fsfw/src/fsfw_hal/linux/CommandExecutor.h
0x4501;UXOS_CommandPending;Command is pending. This will also be returned if the user tries to load another command but a command is still pending;1;LINUX_OSAL;fsfw/src/fsfw_hal/linux/CommandExecutor.h
0x4502;UXOS_BytesRead;Some bytes have been read from the executing process;2;LINUX_OSAL;fsfw/src/fsfw_hal/linux/CommandExecutor.h
0x520a;IMTQ_UnexpectedSelfTestReply;The status reply to a self test command was received but no self test command has been sent. This should normally never happen.;10;IMTQ_HANDLER;mission/acs/imtqHelpers.h
0x53a0;RWHA_InvalidSpeed;Action Message with invalid speed was received. Valid speeds must be in the range of [-65000, 1000] or [1000, 65000];160;RW_HANDLER;mission/acs/RwHandler.h
0x53a1;RWHA_InvalidRampTime;Action Message with invalid ramp time was received.;161;RW_HANDLER;mission/acs/RwHandler.h
0x53a2;RWHA_SetSpeedCommandInvalidLength;Received set speed command has invalid length. Should be 6.;162;RW_HANDLER;mission/acs/RwHandler.h
0x53b1;RWHA_SpiReadFailure;Used by the spi send function to tell a failing read call;177;RW_HANDLER;mission/acs/rwHelpers.h
0x53b2;RWHA_MissingStartSign;Can be used by the HDLC decoding mechanism to inform about a missing start sign 0x7E;178;RW_HANDLER;mission/acs/rwHelpers.h
0x53b3;RWHA_InvalidSubstitute;Can be used by the HDLC decoding mechanism to inform about an invalid substitution combination;179;RW_HANDLER;mission/acs/rwHelpers.h
0x53b4;RWHA_MissingEndSign;HDLC decoding mechanism never receives the end sign 0x7E;180;RW_HANDLER;mission/acs/rwHelpers.h
0x53b5;RWHA_NoReply;Reaction wheel only responds with empty frames.;181;RW_HANDLER;mission/acs/rwHelpers.h
0x53b6;RWHA_NoStartMarker;Expected a start marker as first byte;182;RW_HANDLER;mission/acs/rwHelpers.h
0x53b7;RWHA_SpiReadTimeout;Timeout when reading reply;183;RW_HANDLER;mission/acs/rwHelpers.h
0x54a0;STRH_TemperatureReqFailed;Status in temperature reply signals error;160;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54a8;STRH_FilenameTooLong;Name of file received with command is too long;168;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54a9;STRH_InvalidProgram;Received version reply with invalid program ID;169;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54aa;STRH_ReplyError;Status field reply signals error;170;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54ab;STRH_CommandTooShort;Received command which is too short (some data is missing for proper execution);171;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54ac;STRH_InvalidLength;Received command with invalid length (too few or too many parameters);172;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54ad;STRH_RegionMismatch;Region mismatch between send and received data;173;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54ae;STRH_AddressMismatch;Address mismatch between send and received data;174;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54af;STRH_LengthMismatch;Length field mismatch between send and received data;175;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54b0;STRH_FileNotExists;Specified file does not exist;176;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54b1;STRH_InvalidType;Download blob pixel command has invalid type field;177;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54b2;STRH_InvalidId;Received FPGA action command with invalid ID;178;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54b3;STRH_ReplyTooShort;Received reply is too short;179;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54b4;STRH_CrcFailure;Received reply with invalid CRC;180;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54b5;STRH_StrHelperExecuting;Star tracker handler currently executing a command and using the communication interface;181;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54b6;STRH_StartrackerAlreadyBooted;Star tracker is already in firmware mode;182;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54b7;STRH_StartrackerNotRunningFirmware;Star tracker must be in firmware mode to run this command;183;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x54b8;STRH_StartrackerNotRunningBootloader;Star tracker must be in bootloader mode to run this command;184;STR_HANDLER;mission/acs/str/StarTrackerHandler.h
0x55e0;DWLPWRON_InvalidMode;Received command has invalid JESD mode (valid modes are 0 - 5);224;DWLPWRON_CMD;linux/payload/plocMpsocHelpers.h
0x55e1;DWLPWRON_InvalidLaneRate;Received command has invalid lane rate (valid lane rate are 0 - 9);225;DWLPWRON_CMD;linux/payload/plocMpsocHelpers.h
0x58a1;PLSPVhLP_ProcessTerminated;Process has been terminated by command;161;PLOC_SUPV_HELPER;linux/payload/PlocSupvUartMan.h
0x58a2;PLSPVhLP_PathNotExists;Received command with invalid pathname;162;PLOC_SUPV_HELPER;linux/payload/PlocSupvUartMan.h
0x58a3;PLSPVhLP_EventBufferReplyInvalidApid;Expected event buffer TM but received space packet with other APID;163;PLOC_SUPV_HELPER;linux/payload/PlocSupvUartMan.h
0x5fa0;PLMEMDUMP_MramAddressTooHigh;The capacity of the MRAM amounts to 512 kB. Thus the maximum address must not be higher than 0x7d000.;160;PLOC_MEMORY_DUMPER;linux/payload/PlocMemoryDumper.h
0x5fa1;PLMEMDUMP_MramInvalidAddressCombination;The specified end address is lower than the start address;161;PLOC_MEMORY_DUMPER;linux/payload/PlocMemoryDumper.h
0x60b0;PDEC_CommandNotImplemented;Received action message with unknown action id;176;PDEC_HANDLER;linux/ipcore/pdec.h
0x61a0;CCSDS_CommandNotImplemented;Received action message with unknown action id;160;CCSDS_HANDLER;mission/com/CcsdsIpCoreHandler.h
0x62a0;RS_RateNotSupported;The commanded rate is not supported by the current FPGA design;160;RATE_SETTER;linux/ipcore/PtmeConfig.h
0x62a1;RS_BadBitRate;Bad bitrate has been commanded (e.g. 0);161;RATE_SETTER;linux/ipcore/PtmeConfig.h
0x62a2;RS_ClkInversionFailed;Failed to invert clock and thus change the time the data is updated with respect to the tx clock;162;RATE_SETTER;linux/ipcore/PtmeConfig.h
0x62a3;RS_TxManipulatorConfigFailed;Failed to change configuration bit of tx clock manipulator;163;RATE_SETTER;linux/ipcore/PtmeConfig.h
0x6301;JSONBASE_JsonFileNotExists;Specified json file does not exist;1;ARCSEC_JSON_BASE;mission/acs/str/ArcsecJsonParamBase.h
0x6302;JSONBASE_SetNotExists;Requested set does not exist in json file;2;ARCSEC_JSON_BASE;mission/acs/str/ArcsecJsonParamBase.h
0x6303;JSONBASE_ParamNotExists;Requested parameter does not exist in json file;3;ARCSEC_JSON_BASE;mission/acs/str/ArcsecJsonParamBase.h
0x64a0;NVMB_KeyNotExists;Specified key does not exist in json file;160;NVM_PARAM_BASE;mission/memory/NvmParameterBase.h
0x65a0;FSHLP_SdNotMounted;SD card specified with path string not mounted;160;FILE_SYSTEM_HELPER;bsp_q7s/fs/FilesystemHelper.h
0x65a1;FSHLP_FileNotExists;Specified file does not exist on filesystem;161;FILE_SYSTEM_HELPER;bsp_q7s/fs/FilesystemHelper.h
0x66a0;PLMPHLP_FileWriteError;File error occured for file transfers from OBC to the MPSoC.;160;PLOC_MPSOC_HELPER;linux/payload/PlocMpsocSpecialComHelper.h
0x66a1;PLMPHLP_FileReadError;File error occured for file transfers from MPSoC to OBC.;161;PLOC_MPSOC_HELPER;linux/payload/PlocMpsocSpecialComHelper.h
0x69a2;SPVRTVIF_ReceivedAckFailure;Received ACK failure reply from PLOC supervisor;162;SUPV_RETURN_VALUES_IF;linux/payload/plocSupvDefs.h
0x69a3;SPVRTVIF_ReceivedExeFailure;Received execution failure reply from PLOC supervisor;163;SUPV_RETURN_VALUES_IF;linux/payload/plocSupvDefs.h
0x69a4;SPVRTVIF_InvalidApid;Received space packet with invalid APID from PLOC supervisor;164;SUPV_RETURN_VALUES_IF;linux/payload/plocSupvDefs.h
0x69a5;SPVRTVIF_GetTimeFailure;Failed to read current system time;165;SUPV_RETURN_VALUES_IF;linux/payload/plocSupvDefs.h
0x69a6;SPVRTVIF_InvalidWatchdog;Received command with invalid watchdog parameter. Valid watchdogs are 0 for PS, 1 for PL and 2 for INT;166;SUPV_RETURN_VALUES_IF;linux/payload/plocSupvDefs.h
0x69a7;SPVRTVIF_InvalidWatchdogTimeout;Received watchdog timeout config command with invalid timeout. Valid timeouts must be in the range between 1000 and 360000 ms.;167;SUPV_RETURN_VALUES_IF;linux/payload/plocSupvDefs.h
0x69a8;SPVRTVIF_InvalidLatchupId;Received latchup config command with invalid latchup ID;168;SUPV_RETURN_VALUES_IF;linux/payload/plocSupvDefs.h
0x69a9;SPVRTVIF_SweepPeriodTooSmall;Received set adc sweep period command with invalid sweep period. Must be larger than 21.;169;SUPV_RETURN_VALUES_IF;linux/payload/plocSupvDefs.h
0x69aa;SPVRTVIF_InvalidTestParam;Receive auto EM test command with invalid test param. Valid params are 1 and 2.;170;SUPV_RETURN_VALUES_IF;linux/payload/plocSupvDefs.h
0x69ab;SPVRTVIF_MramPacketParsingFailure;Returned when scanning for MRAM dump packets failed.;171;SUPV_RETURN_VALUES_IF;linux/payload/plocSupvDefs.h
0x69ac;SPVRTVIF_InvalidMramAddresses;Returned when the start and stop addresses of the MRAM dump or MRAM wipe commands are invalid (e.g. start address bigger than stop address);172;SUPV_RETURN_VALUES_IF;linux/payload/plocSupvDefs.h
0x69ad;SPVRTVIF_NoMramPacket;Expect reception of an MRAM dump packet but received space packet with other apid.;173;SUPV_RETURN_VALUES_IF;linux/payload/plocSupvDefs.h
0x69ae;SPVRTVIF_PathDoesNotExist;Path to PLOC directory on SD card does not exist;174;SUPV_RETURN_VALUES_IF;linux/payload/plocSupvDefs.h
0x69af;SPVRTVIF_MramFileNotExists;MRAM dump file does not exists. The file should actually already have been created with the reception of the first dump packet.;175;SUPV_RETURN_VALUES_IF;linux/payload/plocSupvDefs.h
0x69b1;SPVRTVIF_InvalidLength;Received action command has invalid length;177;SUPV_RETURN_VALUES_IF;linux/payload/plocSupvDefs.h
0x69b2;SPVRTVIF_FilenameTooLong;Filename too long;178;SUPV_RETURN_VALUES_IF;linux/payload/plocSupvDefs.h
0x69b3;SPVRTVIF_UpdateStatusReportInvalidLength;Received update status report with invalid packet length field;179;SUPV_RETURN_VALUES_IF;linux/payload/plocSupvDefs.h
0x69b4;SPVRTVIF_UpdateCrcFailure;Update status report does not contain expected CRC. There might be a bit flip in the update memory region.;180;SUPV_RETURN_VALUES_IF;linux/payload/plocSupvDefs.h
0x69b5;SPVRTVIF_SupvHelperExecuting;Supervisor helper task ist currently executing a command (wait until helper tas has finished or interrupt by sending the terminate command);181;SUPV_RETURN_VALUES_IF;linux/payload/plocSupvDefs.h
0x6aa0;ACSCTRL_FileDeletionFailed;File deletion failed and at least one file is still existent.;160;ACS_CTRL;mission/controller/controllerdefinitions/AcsCtrlDefinitions.h
0x6aa1;ACSCTRL_WriteFileFailed;Writing the TLE to the file has failed.;161;ACS_CTRL;mission/controller/controllerdefinitions/AcsCtrlDefinitions.h
0x6aa2;ACSCTRL_ReadFileFailed;Reading the TLE to the file has failed.;162;ACS_CTRL;mission/controller/controllerdefinitions/AcsCtrlDefinitions.h
0x6aa3;ACSCTRL_SingleRwUnavailable;A single RW has failed.;163;ACS_CTRL;mission/controller/controllerdefinitions/AcsCtrlDefinitions.h
0x6aa4;ACSCTRL_MultipleRwUnavailable;Multiple RWs have failed.;164;ACS_CTRL;mission/controller/controllerdefinitions/AcsCtrlDefinitions.h
Status in interface reply signals errorThe status reply to a self test command was received but no self test command has been sent. This should normally never happen.
Status in power reply signals errorAction Message with invalid speed was received. Valid speeds must be in the range of [-65000, 1000] or [1000, 65000]
Received command with invalid length (too few or too many parameters)Can be used by the HDLC decoding mechanism to inform about a missing start sign 0x7E
The capacity of the MRAM amounts to 512 kB. Thus the maximum address must not be higher than 0x7d000.Length in flash write/read reply does not match expected length
Received watchdog timeout config command with invalid timeout. Valid timeouts must be in the range between 1000 and 360000 ms.Filename of file in OBC filesystem is too long
Returned when the start and stop addresses of the MRAM dump or MRAM wipe commands are invalid (e.g. start address bigger than stop address)Space Packet received from PLOC supervisor has invalid CRC
MRAM dump file does not exists. The file should actually already have been created with the reception of the first dump packet.Received execution failure reply from PLOC supervisor
Received update status report with invalid packet length fieldReceived watchdog timeout config command with invalid timeout. Valid timeouts must be in the range between 1000 and 360000 ms.
Update status report does not contain expected CRC. There might be a bit flip in the update memory region.Received latchup config command with invalid latchup ID
Supervisor helper task ist currently executing a command (wait until helper tas has finished or interrupt by sending the terminate command)Received set adc sweep period command with invalid sweep period. Must be larger than 21.
No descriptionReturned when the start and stop addresses of the MRAM dump or MRAM wipe commands are invalid (e.g. start address bigger than stop address)
No descriptionSupervisor helper task ist currently executing a command (wait until helper tas has finished or interrupt by sending the terminate command)
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.